1. Introduction
Thank you for choosing the AXA Ecoline LED 15 Lux Dynamo Bicycle Front Light. This manual provides essential information for the safe and efficient installation, operation, and maintenance of your new bicycle light. This front light is designed to enhance your visibility and illuminate your path during cycling, powered by your bicycle's dynamo system.
2. Safety Instructions
- Always ensure the light is securely mounted before riding.
- Do not look directly into the light beam to avoid temporary vision impairment.
- Ensure all electrical connections to the dynamo are properly insulated and secure to prevent short circuits or damage.
- Regularly check the light for any damage or loose parts. Do not use if damaged.
- This light is designed for bicycle use only.
3. Package Contents
Please check that all items are present in your package:
- AXA Ecoline LED 15 Lux Front Light Unit
- Integrated Mounting Bracket
- Electrical Wire (approx. 10 cm with 2 connections)
4. Setup and Installation
The AXA Ecoline front light is designed for easy fork mounting and dynamo connection.
4.1 Mounting the Light
- Identify the mounting point on your bicycle's front fork. The light comes with an integrated bracket suitable for standard fork mounts.
- Securely attach the light unit to the fork using appropriate bolts and nuts (not included, typically supplied with the bicycle or dynamo). Ensure the light is stable and does not wobble.
- Adjust the angle of the light so that the beam illuminates the road ahead without blinding oncoming traffic. The integrated reflector should face forward.
Figure 1: Side view of the AXA Ecoline front light, showing the integrated mounting bracket and the electrical wire with two connections.
4.2 Connecting to the Dynamo
- Locate the dynamo on your bicycle. This light is compatible with standard bicycle dynamo systems.
- Connect the two wires from the light unit to the corresponding terminals on your dynamo. Ensure correct polarity if specified by your dynamo manufacturer (though many modern dynamos are less sensitive to polarity for lights).
- Secure the wiring along the bicycle frame using cable ties or clips to prevent it from interfering with moving parts or getting damaged.
Figure 2: Front view of the AXA Ecoline light, highlighting the LED lens and the integrated reflector below it.
5. Operating Instructions
The AXA Ecoline front light operates directly from your bicycle's dynamo power.
5.1 Powering On/Off
- The light features an integrated on/off switch. Locate this switch on the light housing.
- To turn the light ON, activate the switch. The light will illuminate when the bicycle is in motion, generating power from the dynamo.
- To turn the light OFF, deactivate the switch.
5.2 Light Performance
- The LED provides a brightness of 15 Lux.
- The light beam has a range of approximately 30 meters, effectively illuminating the path ahead.
- The light offers visibility to other road users from up to 1000 meters away, significantly enhancing safety.
- An integrated reflector provides additional passive safety, reflecting light even when the dynamo is not active.
6. Maintenance
To ensure the longevity and optimal performance of your AXA Ecoline front light, follow these simple maintenance guidelines:
- Cleaning: Wipe the light housing and lens with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the plastic.
- Connections: Periodically check the electrical connections to the dynamo to ensure they are clean, secure, and free from corrosion.
- Mounting: Verify that the light remains securely mounted to the fork. Tighten any loose bolts if necessary.
- Water Resistance: The light is designed to be waterproof. However, avoid submerging it in water or directing high-pressure water jets at it.
7. Troubleshooting
If you encounter issues with your AXA Ecoline front light, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on | Dynamo not generating power, loose electrical connection, switch is OFF, damaged wiring. | Ensure bicycle is moving to activate dynamo. Check all wire connections to the dynamo and light. Verify the on/off switch is in the 'ON' position. Inspect wiring for damage. |
| Light is dim or flickers | Insufficient dynamo power (slow speed), poor electrical connection, dirty dynamo contact. | Increase cycling speed. Check and clean electrical connections. Ensure dynamo is properly engaged with the wheel. |
| Light is loose on the fork | Mounting bolt is loose. | Tighten the mounting bolt securely. |
8. Specifications
| Brand | AXA |
| Model Number | 150360 |
| Light Source | LED |
| Brightness | 15 Lux |
| Power Source | Dynamo-powered (2.4W) |
| Beam Range | 30 meters |
| Visibility | 1000 meters |
| Mounting Type | Fork mount |
| Features | On/off switch, Integrated reflector |
| Material | Plastic |
| Weight | 60 grams |
| Water Resistance | Waterproof |
| Electrical Wire Length | Approx. 10 cm (with 2 connections) |
9. Warranty and Support
This product is covered by a manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty information provided at the point of purchase or contact AXA customer support for details regarding warranty terms and conditions.
For technical support or further assistance, please visit the official AXA website or contact their customer service department. Keep your purchase receipt as proof of purchase.
