Introduction
Thank you for choosing the ARDES BRISA 40PB Pedestal Fan. This manual provides important information for the safe and efficient operation, maintenance, and troubleshooting of your fan. Please read these instructions carefully before use and keep them for future reference.
Safety Information
Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and personal injury.
- Ensure the power supply voltage matches the rating label on the fan.
- Do not operate the fan with a damaged cord or plug.
- Keep fingers and other objects away from the fan blades during operation.
- Do not use the fan in wet or damp environments.
- Unplug the fan from the power outlet before cleaning or performing any maintenance.
- This appliance is for indoor use only.
- Do not allow children to operate the fan unsupervised.
Package Contents
Verify that all components are present:
- 1 x ARDES BRISA 40PB Pedestal Fan Unit (Motor, Blades, Grills, Stand, Base)
- Instruction Manual
Setup and Assembly
Follow these steps to assemble your ARDES BRISA 40PB Pedestal Fan:
- Assemble the Base: Attach the fan stand to the round base. Ensure it is securely fastened.
- Attach the Motor Unit: Secure the motor unit to the top of the stand.
- Install the Rear Grill: Place the rear grill onto the motor unit, aligning it correctly.
- Mount the Blades: Carefully attach the three fan blades to the motor shaft. Ensure they are firmly in place.
- Install the Front Grill: Secure the front grill over the blades and to the rear grill, ensuring it is locked properly.
- Adjust Height: The fan's height is adjustable between 105 cm and 130 cm. Loosen the height adjustment knob on the stand, set to desired height, and tighten securely.
Image: Detailed view of the fan's round base with the interlocking mechanism for stable assembly.
Image: Close-up of the fan head, highlighting its three blades and the control panel with speed settings. The image also indicates a 40 cm diameter.
Image: Diagram showing the fan at two different heights, 105 cm and 120 cm, to demonstrate its adjustable height capability.
Image: The fully assembled ARDES BRISA 40PB pedestal fan, showcasing its design and overall structure.
Operating Instructions
The ARDES BRISA 40PB fan features manual controls located on the neck of the unit.
- Power On/Off: Plug the fan into a suitable 220V power outlet. Use the power button on the control panel to turn the fan on or off.
- Speed Selection: Select one of the three available speeds (1, 2, or 3) using the speed control buttons on the panel. Speed 1 is the lowest, and Speed 3 is the highest.
- Oscillation Function: To activate the automatic lateral oscillation, press the oscillation button on the control panel. Press it again to stop oscillation.
- Tilt Adjustment: The fan head can be manually tilted up or down to direct airflow. Gently adjust the fan head to your desired angle.
Image: Visual representation of the fan's oscillation and tilt capabilities, with arrows indicating movement directions.
Maintenance
Regular cleaning and maintenance will ensure optimal performance and longevity of your fan.
- Cleaning: Always unplug the fan before cleaning. Use a soft, damp cloth to wipe down the exterior surfaces. For the blades and grills, you may need to disassemble the front grill to remove dust buildup. Ensure all parts are dry before reassembling and operating.
- Storage: When not in use for extended periods, store the fan in a cool, dry place, preferably in its original packaging to protect it from dust and damage.
- Do not use abrasive cleaners or solvents, as these can damage the fan's finish.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan does not turn on. | Not plugged in; power outlet not working; power button not pressed. | Ensure fan is securely plugged in. Test the outlet with another device. Press the power button firmly. |
| Weak airflow. | Fan speed set too low; grills or blades are dirty. | Increase the fan speed. Clean the fan blades and grills as per maintenance instructions. |
| Fan makes unusual noise. | Loose parts; fan not on a stable surface; debris in blades. | Check for loose screws or parts and tighten them. Place the fan on a flat, stable surface. Unplug and check for any obstructions around the blades. |
| Oscillation not working. | Oscillation button not pressed; mechanism obstructed. | Press the oscillation button. Ensure there are no obstructions preventing the fan head from rotating. |
Specifications
- Model Name: BRISA
- Model Number: AR5BR40PB
- Brand: Ardes
- Type: Pedestal Fan
- Color: White
- Number of Blades: 3
- Blade Material: Metal
- Diameter: 40 cm (approx. 15.75 inches)
- Number of Speeds: 3
- Wattage: 40 Watts
- Voltage: 220 Volts
- Noise Level: 53 dB(A)
- Airflow Rate: 29.9 Cubic meters per minute
- Adjustable Height: 105 cm to 130 cm
- Features: Oscillating, Tiltable, Silent Operation
- Overall Dimensions (LxWxH): 41 cm x 41 cm x 105-130 cm (adjustable height)
- Weight: 3.5 kg
- Control Type: Manual Panel (Touch/Button)
- Power Source: Corded Electric (Type C Europlug)
- Indoor/Outdoor Use: Indoor
Warranty and Support
This ARDES product comes with a 2-year warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.
For technical support, spare parts, or warranty service, please contact Ardes customer service. Contact information can typically be found on the official Ardes website or on the product packaging.
Manufacturer: Ardes