Introduction
This manual provides essential information for the installation, operation, and maintenance of your Hansgrohe 26842000 Shower Pipe. Please read these instructions carefully before beginning installation or use to ensure proper function and longevity of the product.
The Hansgrohe 26842000 Shower Pipe includes a thermostat for two consumers, a shower head, a shower hose, a shower holder, two glass shelves, and a wall connection. It features an adjustable inclination angle for the vertical shower arm (10 to 30 degrees) and a Rainfinity 360 1jet overhead shower. The hand shower is a Rainfinity 130mm with three jet types, switchable via the Select button.
Setup and Installation
The Hansgrohe 26842000 Shower Pipe is designed for surface installation. Ensure you have the necessary basic body (#26840180) and a concealed thermostat for two functions, as these are sold separately and are required for complete installation. A hand shower 130 3jet (#26864000) and a 160 cm shower hose (#28276000) are also not included and may be required for full functionality.
Components Included:
- Shower head
- Shower hose
- Shower holder
- 2 safety glass shelves
- Wall connection
- Mounting instructions
- Fixing material
- Concealed Shower Pipe unit
Installation Steps:
- Refer to the detailed mounting instructions provided with the product for specific steps.
- Ensure the wall connection and basic body are correctly installed according to the manufacturer's guidelines.
- Mount the Shower Pipe unit to the wall using the provided fixing material.
- Connect the shower head, shower hose, and hand shower (if purchased separately).
- Install the safety glass shelves onto the unit.
Important: All connections should be sealed properly to prevent leaks. If you are unsure about any installation step, consult a qualified plumber.
Figure 1: Technical drawing with dimensions for installation planning.
Operating Instructions
Shower Head (Rainfinity 360 1jet):
The large 360 mm shower head provides a uniform and abundant water flow, offering a luxurious shower experience. The vertical shower arm's inclination can be adjusted between 10 and 30 degrees to direct the water flow as desired.
The primary jet type for the overhead shower is PowderRain, which delivers thousands of micro-fine droplets, creating a soft, enveloping sensation similar to a gentle summer rain.
Figure 2: The PowderRain jet type in use.
Hand Shower (Rainfinity 130mm):
The Rainfinity 130mm hand shower offers three distinct jet types for a personalized shower experience. These can be easily switched by pressing the Select button located on the shower head.
Figure 3: The Select button for changing spray options.
The three jet types typically include:
- PowderRain: Gentle, micro-fine droplets.
- Intense PowderRain: A more concentrated version of PowderRain for invigorating rinse.
- MonoRain: A focused, strong single jet for targeted relief.
Figure 4: Visual representation of the three spray modes.
Thermostat Operation:
The integrated thermostat allows for precise temperature control and easy switching between the overhead and hand showers. Refer to the specific thermostat instructions for detailed temperature adjustment and flow control.
Maintenance
To ensure the longevity and optimal performance of your Hansgrohe Shower Pipe, regular cleaning is recommended.
Cleaning the Shower Heads (QuickClean):
The shower nozzles are equipped with QuickClean technology, designed for easy lime scale removal. Simply rub a cloth over the silicone nozzles to dislodge any accumulated lime scale. This should be done regularly to maintain an even spray pattern.
General Cleaning:
- Use only mild cleaning agents specifically designed for bathroom fixtures.
- Avoid abrasive cleaners, scouring pads, or solvents, as these can damage the chrome finish and glass surfaces.
- Wipe surfaces with a soft, damp cloth and then dry with a clean, soft cloth to prevent water spots.
- Clean the glass shelves with a glass cleaner and a soft cloth.
Troubleshooting
If you encounter any issues with your Hansgrohe Shower Pipe, consider the following common solutions:
- Reduced Water Flow: Check for lime scale buildup on the shower nozzles and clean them using the QuickClean method. Ensure water supply valves are fully open.
- Temperature Fluctuations: Verify that the hot and cold water supplies are correctly connected and that the thermostat is functioning properly. Consult the thermostat's specific manual if issues persist.
- Leaks: Inspect all connections for tightness. If a leak is detected, gently tighten the connection. Do not overtighten. If leaks persist, professional assistance may be required.
For more complex problems, please contact Hansgrohe customer support or a qualified professional.
Specifications
| Feature | Detail |
|---|---|
| Manufacturer | Hansgrohe |
| Model Number | 26842000 |
| Product Dimensions | 45 x 48.2 x 140 cm |
| Weight | 8.69 kg |
| Color | Chrome |
| Finish | Chromed |
| Material | Aluminum (main body), Glass (handle material, shelves) |
| Shape | Round |
| Number of Handles | 3 |
| Mounting Type | Wall Mount |
| Max Flow Rate (at 3 bar) | 19.6 l/min |
| Shower Head Size | 360 mm |
| Adjustable Shower Arm | 10 to 30 degrees inclination |
Warranty Information
Hansgrohe offers a 5-year voluntary manufacturer's warranty on this product, manufactured according to the highest quality standards. This warranty covers defects in materials and workmanship under normal use and service.
For full details and terms of the warranty, please refer to the official Hansgrohe website or contact customer support. Keep your proof of purchase for warranty claims.
Figure 5: Hansgrohe 5-Year Warranty.
Customer Support
Should you require further assistance, have questions about installation, operation, or need to make a warranty claim, please contact Hansgrohe customer support through their official website or the contact information provided in your product packaging.
Please have your model number (26842000) and proof of purchase ready when contacting support.
