myTouchSmart 48707 Rotatable Outdoor Digital Yard Stake Timer Instruction Manual

Introduction

This manual provides detailed instructions for the safe and efficient operation of your myTouchSmart 48707 Rotatable Outdoor Digital Yard Stake Timer. Please read this manual thoroughly before installation and use, and retain it for future reference. This device is designed to automate outdoor lighting and other electrical appliances with programmable on/off times, light-sensing technology, and multiple grounded outlets.

Important Safety Information

• Risk of Electric Shock: Use only with a GFCI-protected outdoor outlet. Do not immerse in water.
• Proper Grounding: Ensure the timer is properly grounded.
• Overload Protection: Do not exceed the maximum electrical rating of 125V, 60 Hz, 1875W (15A) general/resistive.
• Placement: Place the stake in a location with direct access to sunlight for optimal light sensor function. Ensure the unit is at least 1 foot above ground level to prevent waterlogging.
• Outlet Covers: Keep individual self-closing protective outlet covers closed when not in use to prevent moisture and debris entry.
• Cord Management: Route cords to prevent tripping hazards and damage.
• Maintenance: Disconnect power before performing any maintenance or cleaning.

Package Contents

• myTouchSmart Rotatable Outdoor Digital Yard Stake Timer (Model 48707)
• Ground Stake (multi-section)
• Instruction Manual

Product Features

• Rotatable Outlets: Six grounded outlets, three of which rotate 180 degrees for flexible access.
• Digital Timer: Programmable with custom ON/OFF times.
• Light Sensor: Automatic dusk-to-dawn operation or 6-hour countdown after sunset.
• Weather Resistant: Durable construction with self-closing protective outlet covers.
• 10ft Cord: Provides extended reach for outdoor placement.
• Overload Protection: Integrated 15A/1875W circuit breaker for safety.

Setup

1. Assemble the Stake: Attach the stake sections together and then to the timer unit.
2. Placement: Insert the assembled stake firmly into the ground in your desired outdoor location. Ensure the timer unit is at least 1 foot above ground level and has direct access to sunlight if using light-sensing features.
3. Initial Power Connection: Plug the timer's power cord into a GFCI-protected outdoor outlet. If the display is blank, allow the timer to charge for at least 30 minutes to power the internal battery.
4. Reset the Timer: Using a small, non-metallic, insulated tool (like a pencil tip or toothpick), press the RESET button located on the control panel. The LCD display will illuminate and show "12:00 AM".
5. Connect Devices: Plug your outdoor lights or appliances into the grounded outlets. Rotate the outlets as needed for optimal cord management. Close the protective covers over unused outlets.

Operating Instructions

1. Setting Day & Time

1. Press and hold the CLOCK button.
2. While holding CLOCK, press the WEEK button repeatedly until the desired day of the week appears at the top of the display.
3. Continue holding CLOCK, and press the HOUR button repeatedly to set the current hour (AM/PM will adjust automatically).
4. Still holding CLOCK, press the MIN button repeatedly to set the current minute.
5. Release the CLOCK button to save the settings.

2. Setting Programs (ON/OFF Times)

The timer allows for two custom ON/OFF programs. Follow these steps for each program:

1. Press the PROG button once. The display will show "1 ON" at the bottom left. This indicates you are setting the ON time for Program 1.
2. Press the WEEK button repeatedly to select the desired day(s) for this program (e.g., MO, TU, WE, TH, FR, SA, SU, or various combinations).
3. Press the HOUR button to set the desired ON hour.
4. Press the MIN button to set the desired ON minute.
5. Press the PROG button again. The display will show "1 OFF". This indicates you are setting the OFF time for Program 1.
6. Repeat steps 2-4 to set the desired OFF day(s), hour, and minute for Program 1.
7. To set Program 2, press the PROG button again until "2 ON" appears, then repeat steps 2-6.
8. After setting all desired programs, press the CLOCK button to return to the main screen.

To clear a program: While viewing the program (e.g., "1 ON" or "1 OFF"), press the R (Reset) button. Four dashes will appear, indicating the program is cleared. Press R again to reactivate it.

3. Auto/Manual Settings

To use your programmed settings, the timer must be in AUTO mode. To switch between modes:

• Press and hold the MANUAL button for 4 seconds. The display will cycle through AUTO ON, AUTO OFF, and MANUAL.
• AUTO ON: The timer will remain ON until the next programmed OFF time.
• AUTO OFF: The timer will remain OFF until the next programmed ON time.
• MANUAL: The timer will ignore all programmed settings and act as a simple ON/OFF switch.

4. Light Sensor Modes (Dusk-to-Dawn, Countdown)

The timer features light-sensing technology for automatic operation based on ambient light. Ensure the light sensor (located on the top of the unit) is unobstructed and receives direct sunlight for optimal performance.

• Dusk-to-Dawn: The timer will automatically turn ON at dusk and remain ON until dawn.
• Countdown Timer: The timer will turn ON at dusk and remain ON for a preset duration (e.g., 6 hours).

Refer to the specific button on your timer labeled "Sensor" or "Timer" to cycle through these modes. The product description mentions "6-Hour Countdown" and "dawn to dusk" as presets.

5. Security/Vacation Mode (Random Function)

This mode randomly adjusts your programmed ON/OFF times to give your home a lived-in appearance, deterring potential intruders. To activate this feature, you must have at least one program set for longer than 33 minutes.

1. Press the WEEK and HOUR buttons simultaneously. "RND" will appear to the right of the display, indicating Random mode is active.
2. In this mode, programmed ON/OFF times will be randomly postponed by 2 to 32 minutes.
3. To deactivate, press the WEEK and HOUR buttons simultaneously again. "RND" will disappear.

6. Daylight Saving Mode

To adjust the time for Daylight Saving:

1. Press the HOUR and MIN buttons simultaneously. The time will adjust by one hour forward or backward.
2. This function must be manually enabled or disabled as needed.

Maintenance

• Regularly inspect the timer and cord for any signs of damage, fraying, or wear.
• Keep the light sensor clean and free from debris to ensure accurate dusk/dawn detection.
• Ensure all unused outlets have their protective covers securely closed.
• Clean the unit with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.

Troubleshooting

Specifications

Warranty and Support

For warranty information or technical support, please refer to the contact details provided on the product packaging or visit the myTouchSmart official website. Keep your purchase receipt as proof of purchase.