1. Introduction
This manual provides instructions for the installation, operation, and maintenance of the UpStart Components 316442300 8-inch range element replacement. This product is designed to be compatible with various range models, including Frigidaire FFEF3015LSM. Please read this manual thoroughly before proceeding with installation or use to ensure proper function and safety.
Figure 1: Top view of the UpStart Components 8-inch range heating element. This image shows the coiled heating surface and the central support.
2. Safety Information
WARNING: Risk of electric shock. Disconnect power before servicing.
- Always disconnect the power supply to the range or cooktop before attempting any installation, removal, or maintenance procedures. Failure to do so can result in serious injury or death.
- Wear appropriate personal protective equipment, such as gloves, during installation.
- Ensure the replacement element is compatible with your appliance model. Refer to the specifications section and your appliance's service manual.
- If you are unsure about any part of the installation process, consult a qualified appliance technician.
- Do not operate the range if the element is damaged or improperly installed.
3. Installation
Follow these steps to replace your range's 8-inch heating element. These instructions are general; always refer to your specific appliance's service manual for detailed guidance.
- Disconnect Power: Locate the circuit breaker for your range or cooktop and turn it OFF. Alternatively, unplug the appliance from the wall outlet. Verify that power is off before proceeding.
- Remove Old Element: Carefully lift the existing 8-inch heating element from its receptacle. Some elements may require a slight twist or pull to disengage. Note how the element is connected to the terminal block.
- Disconnect Wires: Gently pull the element straight out from the terminal block. The terminals should slide out of the receptacle. Avoid bending or damaging the terminal wires.
- Inspect Terminals: Examine the terminal block and wires for any signs of damage, corrosion, or burning. If damage is present, it may indicate a larger electrical issue that should be addressed by a qualified technician.
- Install New Element: Align the terminals of the new UpStart Components 316442300 element with the receptacle. Push the element firmly and straight into the terminal block until it is fully seated. Ensure a secure connection.
- Seat Element: Carefully lower the element into its designated position on the cooktop, ensuring it sits flat and is properly supported.
- Restore Power: Once the element is securely installed, restore power to the range by turning the circuit breaker ON or plugging the appliance back in.
- Test Functionality: Turn on the burner associated with the newly installed element to a low setting. Observe if the element heats up evenly and glows red. If it does not function correctly, immediately disconnect power and re-check the installation steps.
Figure 2: Angled view of the heating element, highlighting the terminal connections. Ensure these are securely inserted into the range's receptacle.
4. Operation
After successful installation, the 8-inch range element operates identically to the original part. Use your range's control knobs to select the desired heat setting. The element will heat up and glow red, indicating it is active. Always use cookware appropriate for electric coil burners.
- Ensure cookware covers the entire surface of the element for efficient heating.
- Avoid placing empty cookware on a high-heat element for extended periods.
- Do not touch the element when it is hot or glowing.
5. Maintenance
Regular maintenance helps prolong the life of your heating element and ensures safe operation.
- Cleaning: Allow the element to cool completely before cleaning. Wipe spills and food residue from the element and drip pans using a damp cloth and mild detergent. Avoid abrasive cleaners or scouring pads that can damage the element's surface.
- Inspection: Periodically inspect the element for any signs of damage, such as cracks, breaks, or severe discoloration. Check the terminal connections for looseness or corrosion. If any damage is observed, replace the element.
- Drip Pans: Keep drip pans clean to prevent grease buildup, which can be a fire hazard and affect element performance.
6. Troubleshooting
If your newly installed element is not functioning as expected, consider the following common issues:
| Problem | Possible Cause | Solution |
|---|---|---|
| Element does not heat up. |
|
|
| Element heats unevenly or glows only partially. |
|
|
For issues not listed here, or if troubleshooting steps do not resolve the problem, contact customer support.
7. Specifications
- Product Type: 8-inch Range Element Replacement
- Brand: UpStart Components
- Model Number: HE-316442300-2PK-DL1709
- Compatible Part Numbers: 316442300, AP4356466, 08003245, 08013939, 1465860, 222T032P01, 222T032P02, 222T032P03, 222T032P04, 222T032P06, 222T032P06-L, 222T032P07, 222T058P01, 316265600, 318372203, 318372213, 3202348, 382059, 5301314952, 5303015715, 5303207161, 5303311320, 5303325551, 5308005320, 8003245, 8005320, 8013939, A1505255, A1505994, AH2339241, AP382039, AP382044
- Quantity: 2-Pack
- Material: Durable, high-quality construction
- Installation: Easy at-home installation
8. Warranty and Support
This product is an UpStart Components Brand replacement part. Any warranties for this product are offered solely by UpStart Components. This product is not affiliated with any original equipment manufacturer (OEM) brands, and is not covered under any warranties offered by the original manufacturers.
For warranty claims, technical assistance, or support, please contact UpStart Components directly. Refer to the seller information on your purchase receipt for contact details.
Seller: Certified Battery
For further assistance, you may visit the seller's help page: Certified Battery Seller Page