SCUBAPRO Synergy 2 Dive Mask Instruction Manual

1. Introduction

This manual provides essential information for the proper use, care, and maintenance of your SCUBAPRO Synergy 2 Dive Mask. Please read these instructions thoroughly before using the mask to ensure safety and optimal performance. Retain this manual for future reference.

2. Product Features

The SCUBAPRO Synergy 2 Dive Mask is engineered for comfort and clear underwater vision. Key features include:

• Trufit Technology Skirt: Features a double-skirt design with a soft inner silicone for comfort and a firmer outer silicone for support, molding to facial contours for an optimal seal.
• Single Lens Design: Provides an expansive and unobstructed field of view, both horizontally and vertically.
• Easy-to-Use Buckle System: Quick-release buckles attach to the skirt, allowing for easy strap adjustment and enabling the mask to fold flat for travel.
• Ultra-Clear Glass Lens: Ensures bright and clear vision underwater.

Figure 1: SCUBAPRO Synergy 2 Dive Mask (Black)

Figure 2: SCUBAPRO Synergy 2 Dive Mask (Yellow), illustrating the Trufit skirt and buckle attachment.

3. Setup and First Use

3.1 Initial Lens Preparation

New dive masks often have a thin silicone film on the inside of the lens from the manufacturing process, which can cause fogging. To prevent this:

1. Apply a small amount of non-abrasive white toothpaste (not gel) to the inside of the lens.
2. Gently rub the toothpaste over the entire inner surface of the lens with your finger for several minutes.
3. Rinse thoroughly with fresh water to remove all toothpaste residue.
4. Alternatively, use a commercial mask defogger or a mild soap solution before each dive.

3.2 Fitting the Mask

Proper fit is crucial for comfort and to prevent leaks:

1. Place the mask gently on your face without the strap, ensuring your nose is centered in the nose pocket.
2. Inhale gently through your nose. The mask should suction to your face and stay in place without holding it.
3. If the mask does not seal, try adjusting its position or consider if it is the right fit for your face shape.
4. Once a good seal is achieved, place the strap over the back of your head, above your ears.
5. Adjust the strap tension using the quick-release buckles. The strap should be snug enough to hold the mask in place, but not overly tight, as this can cause discomfort and leaks.

4. Operating Instructions

4.1 Donning the Mask

Before entering the water, ensure your hair is clear of the mask skirt to prevent water entry. Place the mask on your face, ensuring the skirt forms a complete seal around your face. The strap should rest comfortably on the back of your head.

4.2 Clearing Water from the Mask

If water enters the mask during a dive:

1. Press the top of the mask frame firmly against your forehead.
2. Exhale slowly and forcefully through your nose. The air will push the water out from the bottom of the mask skirt.
3. Repeat if necessary until the mask is clear.

4.3 Equalization

The nose pocket allows for easy equalization of pressure in your ears and sinuses. Pinch your nose through the flexible nose pocket and gently blow through your nose to equalize as you descend.

5. Maintenance and Care

Proper care extends the life of your dive mask:

• Rinsing: After each use, thoroughly rinse the mask with fresh, clean water to remove salt, chlorine, and sand.
• Drying: Allow the mask to air dry completely in a cool, shaded area, away from direct sunlight. Prolonged exposure to sunlight can degrade silicone and plastic components.
• Storage: Store the mask in its original plastic storage case or a protective bag to prevent scratches and damage. Avoid storing with other gear that could cause pressure or deformation.
• Avoid Chemicals: Do not use harsh chemicals, solvents, or petroleum-based products for cleaning, as these can damage the silicone skirt and lens.
• Inspection: Regularly inspect the mask for any signs of wear, tears in the skirt, or damage to the strap or buckles. Replace damaged components as needed.

6. Troubleshooting

6.1 Mask Fogging

• Ensure initial lens preparation (Section 3.1) was performed thoroughly.
• Apply a commercial anti-fog solution or a small amount of saliva to the inside of the lens before each dive, then rinse lightly.

6.2 Mask Leaking

• Check for hair caught under the mask skirt. Even a single strand can break the seal.
• Ensure the mask strap is not too tight. Overtightening can distort the skirt and cause leaks.
• Verify the mask is centered on your face and the skirt is not folded or creased.
• Facial hair (beards, mustaches) can interfere with the seal. Consider applying a thin layer of silicone grease to the facial hair where the skirt makes contact.

6.3 Discomfort

• Loosen the mask strap. The mask should be held in place by suction, not excessive strap tension.
• Adjust the position of the mask on your face to find the most comfortable fit.

7. Specifications

8. Warranty Information

The SCUBAPRO Synergy 2 Dive Mask comes with a One Year Warranty from the date of purchase. This warranty covers manufacturing defects under normal use. Please retain your proof of purchase for any warranty claims. The warranty does not cover damage resulting from misuse, improper maintenance, or normal wear and tear.

9. Support

For further assistance, technical support, or warranty inquiries, please contact your authorized SCUBAPRO dealer or visit the official SCUBAPRO website. Always refer to the included plastic storage case for additional product information.