1. Introduction
This manual provides essential instructions for the proper installation, operation, and maintenance of the Urmet 1705/701 Wall Mount, designed specifically for Urmet Arktico 2GO video door intercom systems. Please read this manual thoroughly before proceeding with installation to ensure safe and correct usage.
Figure 1: Internal view of the Urmet 1705/701 wall mount module, displaying its circuit board, electronic components, and various connection terminals. This image highlights the technical layout of the device.
2. Setup and Installation
The Urmet 1705/701 wall mount is designed for secure attachment of your Arktico 2GO video door intercom. Proper installation is crucial for the stability and functionality of the intercom system.
2.1. Package Contents
- Urmet 1705/701 Wall Mount Unit
- Mounting Screws and Wall Plugs (may vary by kit)
- Instruction Manual (this document)
2.2. Tools Required
- Drill
- Screwdriver (Phillips head recommended)
- Pencil
- Measuring Tape
- Level
2.3. Installation Steps
- Choose Location: Select a suitable wall location for the video door intercom, ensuring it is at an appropriate height for viewing and operation, and protected from direct weather exposure if outdoors.
- Mark Drilling Points: Place the wall mount unit against the chosen wall and use a pencil to mark the positions for the mounting screws. Use a level to ensure the marks are aligned horizontally.
- Drill Holes: Drill holes at the marked points using an appropriate drill bit size for the provided wall plugs.
- Insert Wall Plugs: Gently insert the wall plugs into the drilled holes until they are flush with the wall surface.
- Mount the Unit: Align the wall mount unit with the drilled holes and secure it to the wall using the provided screws. Ensure the unit is firmly attached and stable.
- Connect Wiring: Refer to the specific wiring diagram of your Urmet Arktico 2GO video door intercom for connecting the necessary cables (power, video, audio, data) to the terminals on the 1705/701 wall mount. Ensure all connections are secure and correctly polarized.
- Attach Intercom: Once the wiring is complete and tested, carefully attach the Arktico 2GO video door intercom unit to the mounted 1705/701 bracket according to the intercom's specific instructions.
Figure 2: A detailed view of the Urmet 1705/701 wall mount's internal components, highlighting the "urmet" branding and the model number "1705/82" (likely a sub-component or internal designation) along with connection points. This image provides a closer look at the wiring interface.
3. Operating Instructions
The Urmet 1705/701 is a passive wall mount designed to securely hold and facilitate the electrical connections for your Urmet Arktico 2GO video door intercom. Its primary function is structural support and providing a stable interface for the intercom's wiring.
- Once installed, the wall mount requires no direct user operation.
- All operational functions are managed through the connected Urmet Arktico 2GO video door intercom unit.
- Ensure the intercom unit is properly seated and secured on the wall mount to maintain stable connections.
4. Maintenance
Regular maintenance helps ensure the longevity and reliable performance of your Urmet 1705/701 wall mount and the attached intercom system.
- Cleaning: Periodically wipe the exterior of the wall mount and intercom with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or excessive moisture.
- Inspection: Annually inspect the mounting screws and the wall mount for any signs of loosening, damage, or corrosion. Tighten screws if necessary.
- Cable Check: Ensure all connected cables remain securely fastened to the terminals and are free from damage or fraying.
- Environmental Protection: If installed outdoors, ensure any protective covers or seals for the intercom system are intact and functioning to prevent water ingress.
5. Troubleshooting
This section addresses common issues related to the wall mount itself. For issues concerning the video door intercom's functionality (e.g., no video, no audio), please refer to the Arktico 2GO intercom's specific manual.
| Problem | Possible Cause | Solution |
|---|---|---|
| Wall mount feels loose or wobbly. | Mounting screws are loose; wall plugs are not secure; wall material is compromised. | Tighten mounting screws. If still loose, inspect wall plugs and wall integrity. Consider using larger plugs or relocating if wall is damaged. |
| Intercom unit does not sit flush on the mount. | Obstruction behind the intercom; incorrect alignment during attachment. | Remove intercom and check for any debris or misaligned cables. Re-attach carefully, ensuring proper seating. |
| Intermittent connection issues (e.g., flickering video, distorted audio). | Loose or corroded wiring connections on the wall mount terminals. | WARNING: Disconnect power before inspecting wiring. Check all wire connections to the wall mount terminals. Ensure they are clean, tight, and correctly inserted. |
6. Specifications
| Attribute | Detail |
|---|---|
| Manufacturer | URMET |
| Model Number | 1705/701 |
| Compatibility | Urmet Arktico 2GO Video Door Intercom Systems |
| ASIN | B084G9MN2K |
| First Available Date | April 29, 2020 |
| Guaranteed Software Updates Until | Unknown (N/A for a passive wall mount) |
7. Support Information
For further assistance, technical support, or warranty inquiries regarding your Urmet 1705/701 Wall Mount or Urmet Arktico 2GO intercom system, please contact Urmet customer service or visit their official website. Contact details are typically found on the manufacturer's packaging or their official online portal.
Note: As this is a passive mounting accessory, software updates are not applicable to the wall mount itself. Any software-related inquiries should be directed to the manufacturer of the connected intercom unit.
