1. Important Safety Information
Please read all instructions carefully before assembly and use. Retain this manual for future reference.
- Electrical Safety: Always disconnect the power supply before cleaning or performing any maintenance. Do not operate the lamp with a damaged cord or plug.
- Integrated LED: The LED lights in this lamp are integrated and are not replaceable. They are designed for a long lifespan of approximately 50,000 hours.
- Assembly Caution: During assembly, carefully inspect the wiring at the base connection point. Some units may have a thin wire that can become exposed or cut during manufacturing or shipping. If you observe any exposed or damaged wires, DO NOT PROCEED WITH ASSEMBLY OR USE. Contact customer support immediately.
- Indoor Use Only: This lamp is designed for indoor use in dry locations. Do not expose to water or excessive humidity.
- Stable Placement: Ensure the lamp is placed on a stable, level surface to prevent tipping.
2. Package Contents
Verify that all components are present and undamaged before proceeding with assembly.
- Marla LED Wall Washer Floor Lamp (Main Pole with integrated LED)
- Lamp Base
- Assembly Hardware (if applicable, typically pre-attached or minimal)
3. Setup and Assembly
Follow these steps to assemble your Adesso Marla LED Wall Washer Floor Lamp:
- Unpack Components: Carefully remove all parts from the packaging. Place them on a soft, clean surface to prevent scratches.
- Inspect Wiring: Before attaching the base, carefully examine the electrical wire where it exits the bottom of the main lamp pole and where it connects to the base. Ensure there are no cuts, fraying, or exposed metal strands. If any damage is found, do not proceed and contact customer support.
- Attach Base: Align the main lamp pole with the lamp base. Gently thread the pole into the base, turning clockwise until securely tightened. Ensure the power cord is not twisted or pinched during this step.
- Position Lamp: Place the assembled lamp in your desired indoor location, ensuring it is on a stable, level surface.
- Connect Power: Plug the power cord into a standard 120V AC electrical outlet.
4. Operating Instructions
The Adesso Marla LED Wall Washer Floor Lamp features intuitive touch controls located on the main pole for power, brightness, and color temperature adjustments.
4.1 Power On/Off
- Touch the Power button (circle with vertical line) once to turn the lamp ON.
- Touch the Power button again to turn the lamp OFF.
4.2 Adjusting Brightness Levels
The lamp offers 6 distinct brightness levels.
- With the lamp ON, touch the Brightness buttons (snowflake-like icons) to cycle through the 6 available brightness settings.
- Each touch will increase or decrease the brightness, depending on the direction of the icons.
4.3 Adjusting Color Temperature
The lamp provides 5 different color temperature modes to suit various environments and preferences.
- With the lamp ON, touch the Mode button (letter 'M') to cycle through the following color temperature settings:
- 6500K (Cool Daylight)
- 5700K (Cool White)
- 4500K (Neutral White)
- 3968K (Warm White)
- 3500K (Soft White)
- 3000K (Warm Glow)
5. Maintenance
Proper care will ensure the longevity and optimal performance of your lamp.
- Cleaning: Disconnect the lamp from the power source before cleaning. Use a soft, dry cloth to wipe the lamp's surface. Do not use abrasive cleaners, solvents, or polishes as they may damage the finish or electrical components.
- LED Lifespan: The integrated LED lights are designed to last approximately 50,000 hours and do not require replacement.
- Storage: If storing the lamp, ensure it is clean and dry. Store in a cool, dry place away from direct sunlight and extreme temperatures.
6. Troubleshooting
If you encounter issues with your lamp, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not turn on. | 1. Power cord not securely plugged in. 2. No power from outlet. 3. Damaged internal wiring (refer to Safety Information). | 1. Ensure the power cord is fully inserted into the outlet. 2. Test the outlet with another device. Check circuit breaker. 3. If damaged wiring is suspected, discontinue use and contact customer support. |
| Light output is inconsistent or flickers. | 1. Loose connection. 2. Electrical interference. | 1. Ensure all connections are secure. Unplug and replug the lamp. 2. Move the lamp away from other electronic devices. |
| Touch controls are unresponsive. | 1. Power interruption. 2. Sensor obstruction. | 1. Unplug the lamp for 30 seconds, then plug it back in. 2. Ensure the touch control area is clean and free from obstructions. |
If the problem persists after attempting these solutions, please contact Adesso customer support.
7. Specifications
| Brand | Adesso |
| Model Name | Marla LED Wall Washer |
| Model Number | 2101-22 |
| Dimensions | 9.5"W x 48.5"H |
| Material | Metal (Brushed Steel) |
| Light Source | Integrated LED |
| Wattage | 32 Watts |
| Brightness | 2200 Lumens (Maximum) |
| Color Temperature Settings | 6500K, 5700K, 4500K, 3968K, 3500K, 3000K |
| Control Method | Touch Control |
| Voltage | 120 Volts |
| Average Life | 50,000 Hours |
| Item Weight | 11.43 pounds |
8. Warranty and Support
For warranty information, please refer to the documentation included with your purchase or visit the official Adesso website. If you require technical assistance or have questions not covered in this manual, please contact Adesso customer support.
Adesso Customer Support:
Please refer to the contact information provided on the product packaging or the official Adesso website for the most current support details.
