Eibach Pro-Lift Kit +30mm Suspension Springs for VW Amarok 2HS2 (Model 45010)

1. Product Overview

The Eibach Pro-Lift Kit is designed to enhance the appearance and performance of your vehicle by providing an additional 30mm of ground clearance. This kit allows for improved off-road capability while maintaining the vehicle's original ride comfort. It is specifically engineered for the VW Amarok (4WD) Type 2HS2, manufactured from June 2016 onwards.

2. Package Contents

Please verify that all components listed below are present and undamaged before beginning installation.

• 2 x Pro-Lift Suspension Springs for the Front Axle
• 2 x 30mm Spacers for Leaf Springs (Rear Axle)
• 4 x Spring Brackets (U-bolts)
• Mounting Hardware (nuts, washers, etc.)
• Installation Instructions (may be in German)
• TÜV Certificate

Figure 1: Overview of the Eibach Pro-Lift Kit components. This image displays the two front suspension springs, two rectangular rear leaf spring spacers, and four U-shaped spring brackets with nuts, which constitute the main parts of the lift kit.

3. Compatibility and Important Notes

• Vehicle Manufacturer: VW
• Vehicle Model: Amarok (4WD)
• Vehicle Type: 2HS2 (6-cylinder models)
• Year of Manufacture: From 06/2016 onwards
• Important: Only suitable for vehicles without level control or air suspension.
• Important: Not suitable for vehicles with 5 leaf springs at the rear.
• This kit includes a TÜV certificate for compliance.

4. Setup and Installation

Installation of suspension components requires specialized tools and expertise. It is highly recommended that this kit be installed by a qualified automotive technician. Improper installation can lead to vehicle instability, component failure, and serious injury.

4.1 Pre-Installation Checks

• Ensure the vehicle is on a level, stable surface and properly secured with jack stands.
• Review the complete installation instructions provided with the kit before starting.
• Confirm all package contents are present and undamaged (refer to Section 2).
• Gather all necessary tools, including torque wrenches, spring compressors (if required for front springs), and general automotive tools.

4.2 General Installation Steps (Summary)

Note: This is a general overview. Always follow the detailed instructions provided with your Eibach Pro-Lift Kit.

1. Safely lift the vehicle and remove the wheels.
2. Front Axle: Carefully remove the original front suspension springs. Install the new Eibach Pro-Lift front springs, ensuring proper seating and orientation.
3. Rear Axle: Support the rear axle. Remove the existing U-bolts. Insert the 30mm leaf spring spacers between the leaf spring pack and the axle. Secure the assembly using the new, longer U-bolts and mounting hardware.
4. Tighten all fasteners to the manufacturer's specified torque values.
5. Reinstall wheels and lower the vehicle.
6. Perform a wheel alignment immediately after installation to ensure correct steering and tire wear.

Figure 2: Close-up of the four U-bolts included in the kit. These U-bolts are essential for securing the leaf spring assembly and the new spacers to the rear axle.

Figure 3: The two 30mm leaf spring spacers. These rectangular blocks are placed between the leaf springs and the axle to achieve the desired lift at the rear of the vehicle.

5. Operating Considerations

After installing the Pro-Lift Kit, your vehicle's handling characteristics may change. Be aware of the following:

• Center of Gravity: The vehicle's center of gravity will be higher, which can affect stability, especially during sharp turns or emergency maneuvers. Drive cautiously until you are accustomed to the new handling.
• Braking: Braking distances may be slightly altered.
• Off-Road Driving: While the kit enhances off-road capability, always exercise caution and drive within the limits of your vehicle and your skill level.
• Tire Pressure: Check and adjust tire pressure as recommended for your vehicle and any new tire sizes.

6. Maintenance

Regular inspection and maintenance are crucial for the longevity and safe operation of your Eibach Pro-Lift Kit.

• Initial Check (500 km / 300 miles): After the first 500 kilometers (approximately 300 miles) of driving, re-check all fasteners, especially the U-bolts and spring mounting bolts, for proper torque. Re-tighten if necessary.
• Routine Inspection: Periodically inspect all suspension components for signs of wear, damage, or corrosion. This includes springs, spacers, U-bolts, and associated bushings.
• Cleaning: Keep suspension components clean, especially after off-road use, to prevent dirt and debris buildup that can accelerate wear.
• Alignment: Have your vehicle's wheel alignment checked annually or if you notice uneven tire wear or steering issues.

7. Troubleshooting

If you experience any issues after installing the Eibach Pro-Lift Kit, consider the following common troubleshooting steps:

• Unusual Noises (Clunking/Squeaking):
  • Check all mounting bolts and nuts for proper torque. Loose fasteners are a common cause of noise.
  • Inspect for any components rubbing against each other or the chassis.
  • Ensure springs are correctly seated in their perches.
• Uneven Ride Height:
  • Verify that the correct springs and spacers were installed on the appropriate axles.
  • Ensure all components are fully seated and not binding.
  • Confirm vehicle compatibility (e.g., not for 5-leaf spring rear axles).
• Poor Handling/Steering Issues:
  • Immediately have a professional wheel alignment performed.
  • Check for loose steering or suspension components.
  • Ensure tire pressures are correct.

If troubleshooting steps do not resolve the issue, contact a qualified automotive technician or Eibach customer support for assistance.

8. Specifications

9. Warranty and Support

Eibach products are manufactured to high-quality standards. For specific warranty information, please refer to the documentation included with your purchase or visit the official Eibach website. For technical support or inquiries regarding your Pro-Lift Kit, please contact Eibach customer service directly.

Always ensure you are using genuine Eibach parts for replacements to maintain product integrity and performance.