Metabo 602207550 BS18 Cordless Drill/Driver Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Metabo BS18 Cordless Drill/Driver. Please read these instructions carefully before using the tool and keep them for future reference.

The Metabo BS18 is a compact and lightweight cordless drill/driver designed for various drilling and screwdriving applications. It features an integrated work light and a practical belt hook for convenience.

1.1 Included Components

• Metabo BS18 Cordless Drill/Driver
• 2 x Metabo Li-Power 18V 1.5Ah Lithium-ion Batteries
• Metabo SC 60 Plus Charger
• Quick-clamping Chuck
• Belt Hook
• Plastic Carry Case

2. General Safety Instructions

Always observe the following basic safety precautions when using electric tools to reduce the risk of electric shock, fire, and serious injury.

2.1 Work Area Safety

• Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2.2 Electrical Safety

• Power tool plugs must match the outlet. Never modify the plug in any way.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

2.3 Personal Safety

• Always wear eye protection. Use safety glasses, goggles, or a face shield.
• Wear appropriate personal protective equipment (PPE) such as dust masks, non-skid safety shoes, hard hats, or hearing protection when necessary.
• Stay alert, watch what you are doing, and use common sense when operating a power tool.
• Do not overreach. Keep proper footing and balance at all times.

3. Product Components

Familiarize yourself with the main parts of your Metabo BS18 drill/driver.

• Quick-clamping Chuck: For quick and easy bit changes.
• Torque Selector Ring: Adjusts the torque setting for screwdriving applications.
• Speed Selector Switch: Selects between two speed ranges (e.g., low speed for high torque, high speed for drilling).
• Forward/Reverse Switch: Controls the direction of rotation.
• Trigger Switch: Activates the tool and controls speed (variable speed).
• Integrated Work Light: Illuminates the work area.
• Battery Pack: Removable 18V Li-ion battery.
• Belt Hook: Attachable to either side of the tool for convenient carrying.

4. Setup and Preparation

4.1 Charging the Battery

1. Connect the SC 60 Plus charger to a suitable power outlet.
2. Slide the battery pack into the charger until it clicks into place.
3. The charger's indicator light will show the charging status. Refer to the charger's manual for specific light patterns.
4. Once fully charged, remove the battery from the charger.

Note: For optimal battery life, avoid deep discharge and store batteries in a cool, dry place.

4.2 Inserting and Removing the Battery

• Inserting: Align the battery pack with the base of the drill handle and slide it in until it locks securely.
• Removing: Press the release buttons on the sides of the battery pack and slide it out.

4.3 Attaching and Removing Bits

1. Ensure the tool is switched off and the forward/reverse switch is in the neutral (locked) position.
2. Rotate the quick-clamping chuck counter-clockwise to open the jaws.
3. Insert the drill bit or screwdriver bit into the chuck as far as it will go.
4. Rotate the chuck clockwise to tighten the jaws securely around the bit. Ensure the bit is centered and firmly held.
5. To remove, rotate the chuck counter-clockwise and pull the bit out.

4.4 Attaching the Belt Hook

The practical belt hook can be attached to either the left or right side of the tool without the need for additional tools. Simply align the hook with the designated slot on the drill body and push until it clicks into place. To remove, gently pull it off.

5. Operating Instructions

5.1 Powering On/Off and Speed Control

• To turn the tool on, press the trigger switch. The integrated work light will illuminate.
• To turn the tool off, release the trigger switch.
• The speed is variable and controlled by the pressure applied to the trigger switch. Pressing harder increases the speed.

5.2 Selecting Rotation Direction

Use the forward/reverse switch located above the trigger to select the desired rotation direction:

• Push the switch to the left for forward rotation (for drilling and tightening screws).
• Push the switch to the right for reverse rotation (for loosening screws).
• When the switch is in the center position, the trigger is locked, preventing accidental startup.

5.3 Adjusting Torque and Speed

• Torque Setting: Rotate the torque selector ring to choose the appropriate torque for screwdriving. Lower settings are for smaller screws or softer materials, higher settings for larger screws or harder materials. The drill setting bypasses the clutch for maximum power.
• Speed Range: Use the speed selector switch (typically on top of the drill) to choose between two speed ranges. Position '1' is for lower speed and higher torque (e.g., screwdriving), and position '2' is for higher speed and lower torque (e.g., drilling).

5.4 Drilling and Screwdriving

• Always secure the workpiece to prevent movement.
• For drilling, select the drill mode on the torque ring and the appropriate speed range. Apply steady, even pressure.
• For screwdriving, select a suitable torque setting and speed range. Start with a lower torque setting and increase if necessary to avoid stripping screw heads or damaging the material.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your tool.

6.1 Cleaning

• Always remove the battery pack before cleaning.
• Keep the ventilation openings of the tool clean to prevent overheating.
• Wipe the tool housing with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Clean the chuck jaws regularly to ensure proper grip on bits.

6.2 Battery Care and Storage

• Store batteries in a cool, dry place, away from direct sunlight and extreme temperatures.
• Do not store fully discharged batteries for extended periods. Charge them periodically if not in use.
• Protect batteries from impact and moisture.

6.3 General Inspection

Periodically check for any loose screws, damaged parts, or excessive wear. If any issues are found, contact an authorized service center for repair.

7. Troubleshooting

This section addresses common issues you might encounter with your Metabo BS18 drill/driver.

8. Technical Specifications

9. Warranty and Support

9.1 Warranty Information

Metabo offers a 3-year warranty on the battery packs, ensuring maximum power and safe charging through their Ultra-M Technology. For specific warranty terms and conditions for the tool itself, please refer to the documentation provided with your purchase or visit the official Metabo website.

9.2 Customer Support

For technical assistance, spare parts, or service inquiries, please contact your authorized Metabo dealer or visit the official Metabo website for contact information in your region. When contacting support, please have your product model number (602207550) and serial number ready.