1. Introduction and Overview
The Delta 10 in. Portable Contractor Table Saw is engineered for precision and efficiency in woodworking tasks. Designed for both amateur and professional use, this saw offers robust performance in a portable form factor, making it ideal for various job sites and workshops.
Key features include:
- Retractable Blade: Blade retracts below the table top for easy clean-up and enhanced safety.
- Durable Construction: Features an aluminum table top with an extension providing 45-3/4 inches of support, and a rear table extension for workpiece support.
- Powerful Motor: Equipped with a 15 amp motor capable of powering through tough materials like pressure-treated lumber and hardwood flooring.
- Portability: Weighing less than 65 lbs., this saw is easily transported and stored.
- High Capacity: Offers a maximum rip capacity of 25 inches to the right of the blade and 12 inches to the left.
2. Safety Information
Always prioritize safety when operating power tools. Failure to follow these instructions may result in serious injury or death.
- Read the Manual: Before operation, thoroughly read and understand all instructions and warnings in this manual.
- Personal Protective Equipment (PPE): Always wear safety glasses, hearing protection, and a dust mask. Avoid loose clothing or jewelry that could get caught in moving parts.
- Power Disconnection: Disconnect the saw from the power source before making any adjustments, changing blades, or performing maintenance.
- Work Area: Ensure your work area is clean, well-lit, and free of obstructions. Keep children and bystanders away.
- Blade Safety: Never place hands near the rotating blade. Use a push stick or push block when cutting small pieces. Ensure the blade guard is always in place and functioning correctly.
- Kickback Prevention: Use the rip fence correctly, avoid cutting warped or twisted wood, and never stand directly in line with the blade.
- Proposition 65 Warning: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
3. Package Contents
Verify that all items are present upon unpacking:
- Delta 10 in. Portable Contractor Table Saw Unit
- 10-inch Carbide Blade
- Blade Guard Assembly
- Rip Fence
- Miter Gauge
- Push Stick
- Wrenches for blade changes
- Instruction Manual
4. Setup
Follow these steps to set up your table saw for operation:
- Unpacking: Carefully remove all components from the packaging. Inspect for any shipping damage.
- Placement: Place the saw on a stable, level surface. The saw's design allows for easy transport and storage, but ensure it is secure during operation.
- Blade Installation:
- Ensure the saw is unplugged.
- Raise the blade arbor to its maximum height.
- Using the provided wrenches, loosen the arbor nut and remove the outer blade flange.
- Place the 10-inch carbide blade onto the arbor with the teeth pointing towards the front of the saw.
- Reinstall the outer blade flange and tighten the arbor nut securely.
- Blade Guard Assembly: Attach the blade guard and anti-kickback pawls according to the diagrams in the full manual. Ensure they move freely and provide adequate protection.
- Rip Fence Installation and Calibration:
- Slide the rip fence onto the front and rear rails.
- Engage the locking mechanism.
- Verify the fence is parallel to the blade. If not, refer to the detailed manual for calibration instructions. The rack and pinion fence system is designed for precise adjustments.
- Table Extension: Extend the aluminum table top as needed for larger workpieces. Ensure it is securely locked in place.
- Dust Port Connection: Connect a shop vacuum or dust collection system to the 2.5-inch dust port for efficient debris removal.
Figure 4.1: The Delta 10 in. Portable Contractor Table Saw, showing the main unit with blade guard and rip fence.
5. Operating Instructions
This section outlines the basic operation of your table saw.
- Power Connection: Plug the saw into a standard 120V, 60Hz electrical outlet. Ensure the circuit can handle the 15 amp motor.
- Blade Height Adjustment: Use the handwheel to raise or lower the blade. For most cuts, the blade should extend approximately 1/8 inch above the workpiece.
- Bevel Angle Adjustment: Loosen the bevel lock and tilt the blade to the desired angle (0 to 45 degrees). Tighten the lock securely before cutting. Max. Depth of Cut at 90º is 3.5 in. (88.9mm); Max. Depth of Cut at 45º is 2.5 in. (63.5mm).
- Rip Cut Setup:
- Position the rip fence to the desired width using the measurement scale.
- Lock the fence firmly in place.
- Max. Rip Right of Blade is 25 in. (762mm); Max. Rip Left of Blade is 12 in. (304.8mm).
- Crosscut Setup: Use the miter gauge for accurate crosscuts. Ensure the miter gauge slides smoothly in the miter slot.
- Starting the Saw: Press the ON button. Allow the blade to reach full 5000 RPM speed before beginning the cut.
- Making a Cut:
- Feed the workpiece slowly and steadily into the blade.
- Maintain firm contact with the table and fence/miter gauge.
- Always use a push stick for narrow cuts or when your hands are close to the blade.
- Dado Cuts: The saw supports a Dado Capacity of 0.8125 in. x 8 in. Refer to the full manual for detailed instructions on installing and using a dado blade set.
- Stopping the Saw: Press the OFF button. Wait for the blade to come to a complete stop before leaving the saw or reaching near the blade.
Figure 5.1: Front view of the table saw, highlighting the blade height and bevel adjustment controls.
6. Maintenance
Regular maintenance ensures optimal performance and extends the life of your table saw.
- Cleaning: After each use, disconnect power and clean the table top, fence, and blade area. Remove sawdust and debris, especially from below the unit, as dust collection may not be perfect.
- Blade Inspection: Regularly inspect the blade for sharpness, damage, or missing teeth. Replace dull or damaged blades promptly.
- Fence and Rail Cleaning: Keep the rip fence and its rails clean and free of sawdust to ensure smooth and accurate movement.
- Motor Vents: Ensure motor cooling vents are clear of dust and debris to prevent overheating.
- Cord Inspection: Check the power cord for any signs of damage or fraying.
7. Troubleshooting
This section addresses common issues you might encounter.
| Problem | Possible Cause | Solution |
|---|---|---|
| Saw does not start | No power, tripped breaker, faulty switch | Check power connection, reset breaker, contact service if switch is faulty. |
| Table top not flat | Manufacturing variation, improper support | Verify saw is on a level surface. For significant flatness issues, contact Delta customer support. |
| Rip fence does not lock securely or is inaccurate | Debris on rails, misaligned locking mechanism, calibration needed | Clean rails, inspect locking lever, recalibrate fence parallel to blade as per manual. |
| Excessive blade vibration | Dull or damaged blade, improperly installed blade, loose arbor nut | Replace blade, ensure blade is installed correctly and arbor nut is tight. |
| Poor dust collection | Clogged dust port, inadequate vacuum system | Clear dust port, ensure strong vacuum connection. Regular manual cleaning below the unit may be necessary. |
8. Specifications
| Attribute | Value |
|---|---|
| Brand | Delta |
| Model Number | 36-6013 |
| Power Source | Corded Electric |
| Voltage | 120 Volts |
| Wattage | 1800 watts |
| Motor Amperage | 15 Amps |
| No-Load Speed | 5000 RPM |
| Blade Diameter | 10 Inches |
| Arbor Size | 0.625 in. (15.875mm) |
| Max. Depth of Cut at 90º | 3.5 in. (88.9mm) |
| Max. Depth of Cut at 45º | 2.5 in. (63.5mm) |
| Max. Rip Right of Blade | 25 in. (762mm) |
| Max. Rip Left of Blade | 12 in. (304.8mm) |
| Dado Capacity | 0.8125 in. x 8 in. |
| Dust Port Size | 2.5 in. (63.5mm) |
| Product Dimensions (L x W x H) | 45.75 in. x 24.5 in. x 36.44 in. (1162.05mm x 647.70mm x 925.51mm) |
| Item Weight | 64.7 lbs. (29.35 kg) |
| Included Components | Carbide Blade |
| UPC | 847962006387 |
9. Warranty and Support
Warranty: The Delta 10 in. Portable Contractor Table Saw comes with a 5 Year Professional Warranty. Please retain your proof of purchase for warranty claims.
Returns: This product is eligible for 30-day easy returns. Refer to your retailer's return policy for details.
Customer Support: For technical assistance, parts, or warranty service, please contact Delta Power Equipment Corporation customer support. Visit the official Delta website for contact information and additional resources.
You can find more information and support at the Delta Brand Store on Amazon.
