ECOXGEAR Boulder Replacement Battery Instruction Manual

1. Product Overview

This manual provides essential information for the Beiter DC Power 12V 7AH Sealed Lead Acid (SLA) replacement battery, specifically designed for use with ECOXGEAR Boulder portable speakers. This battery is engineered to provide reliable power and is a direct replacement for the original battery in compatible devices.

Image 1.1: The Beiter DC Power 12V 7AH SLA Replacement Battery, showing its black casing and terminal connections.

The battery is a high-performance, maintenance-free, and valve-regulated unit, ensuring safe and trouble-free operation. It features a rugged construction with a high-impact resistant ABS plastic case, providing durability against shock, vibration, chemicals, and heat.

2. Key Features

• High Performance: Designed to deliver consistent power output for your device.
• Maintenance-Free: No need for water refilling or specific maintenance routines.
• Valve Regulated: Ensures safe operation by controlling internal pressure.
• Spill-Proof Design: Allows for versatile installation in various orientations without leakage.
• Rugged Construction: Encased in non-conductive ABS plastic, resistant to shock, vibration, chemicals, and heat.
• Fiberglass Mat Technology: Utilizes a fine fiberglass mat for efficient electrolyte absorption.

3. Installation and Setup

Before beginning the installation, ensure your ECOXGEAR Boulder speaker is powered off and disconnected from any charging source. Refer to your speaker's original instruction manual for specific battery compartment access and removal procedures.

3.1 Identifying Terminals

The battery features clearly marked positive (+) and negative (-) terminals. The positive terminal is typically red, and the negative terminal is black or grey. Ensure correct polarity when connecting the battery to your device's wiring harness.

Image 3.1: Close-up view of the battery terminals, showing the distinct positive (red) and negative (black/grey) connections.

3.2 Installation Steps

1. Carefully open the battery compartment of your ECOXGEAR Boulder speaker as per its manual.
2. Disconnect the existing battery, noting the positive and negative connections.
3. Remove the old battery.
4. Insert the new Beiter DC Power replacement battery into the compartment, ensuring it fits securely.
5. Connect the wiring harness to the new battery's terminals, matching positive to positive and negative to negative.
6. Close the battery compartment.
7. It is recommended to fully charge the battery before first use.

4. Operating the Battery

This 12V 7AH SLA battery functions as the power source for your ECOXGEAR Boulder speaker. Once installed and charged, it will power the device. The battery is designed for deep cycle applications, meaning it can be discharged significantly and recharged multiple times.

4.1 Charging

Charge the battery using the charger provided with your ECOXGEAR Boulder speaker. Ensure the charger is compatible with 12V SLA batteries. Overcharging or undercharging can reduce battery life. The battery is designed to be charged within a voltage range of 13.5-13.8V for standby use and 14.5-14.9V for cycle use.

4.2 Discharge

The battery will discharge as your device consumes power. For optimal battery life, avoid completely draining the battery whenever possible. Recharge the battery promptly after use, especially after significant discharge.

5. Maintenance and Storage

While this battery is maintenance-free, proper care and storage practices will extend its lifespan.

• Regular Charging: If the battery is not in regular use, charge it every 3-6 months to prevent self-discharge and maintain capacity.
• Clean Terminals: Keep battery terminals clean and free of corrosion. Use a dry cloth to wipe them if necessary.
• Storage Temperature: Store the battery in a cool, dry place, away from direct sunlight and extreme temperatures. Ideal storage temperature is between 20°C and 25°C (68°F and 77°F).
• Avoid Short Circuits: Do not allow metal objects to bridge the battery terminals, as this can cause a short circuit and damage the battery.

6. Troubleshooting

If you experience issues with your replacement battery, consider the following troubleshooting steps:

• Device Not Powering On:
  • Ensure the battery is fully charged.
  • Verify that the battery terminals are correctly connected to the device's wiring harness (positive to positive, negative to negative).
  • Check for any loose connections or corrosion on the terminals.
• Battery Not Holding Charge:
  • Confirm that your charger is functioning correctly and is compatible with 12V SLA batteries.
  • Ensure the battery has been charged for the recommended duration.
  • If the battery is old, its capacity may have naturally degraded over time.
• Reduced Operating Time:
  • This can indicate a partially charged battery or a battery nearing the end of its service life.
  • Ensure the battery is fully charged before each use.

If issues persist after following these steps, contact Beiter DC Power customer support or consult a qualified technician.

7. Specifications

Image 7.1: Dimensions of the 12V 7AH SLA Battery, illustrating its length, width, and height.

Image 7.2: Internal structure of a Sealed Lead Acid battery, illustrating the plates, separators, and electrolyte.

8. Safety Information

Please read and adhere to the following safety precautions to prevent injury or damage to the battery and your device.

• Proposition 65 Warning: This product may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
• Do Not Disassemble: Do not attempt to open or disassemble the battery. There are no user-serviceable parts inside.
• Avoid Short Circuits: Do not short-circuit the battery terminals with metal objects. This can cause sparks, heat, and potential fire or explosion.
• Proper Ventilation: Although sealed, ensure adequate ventilation during charging to dissipate any minimal gases that may be released.
• Temperature Limits: Do not expose the battery to extreme temperatures (above 50°C/122°F or below -15°C/5°F).
• Disposal: Do not dispose of the battery in household waste or by incineration. SLA batteries contain lead and must be recycled properly.

Image 8.1: Universal recycling symbol for batteries, emphasizing the importance of proper disposal.

Always handle batteries with care and keep them out of reach of children.

9. Warranty and Support

This Beiter DC Power battery comes with a limited warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or contact Beiter DC Power directly.

Return Policy: Products purchased from Beiter DC Power typically have a 30-day return policy. Please check your purchase details for exact terms.

For technical support, troubleshooting assistance, or warranty claims, please contact Beiter DC Power customer service through their official channels. You can often find contact information on their Amazon store page or official website.

Visit the Beiter DC Power Store on Amazon for more information.