Vantrue 11.5ft USB-C Hardwire Kit Instruction Manual

Introduction

The Vantrue 11.5ft USB-C Hardwire Kit is designed to provide a continuous power supply to your dash cam directly from your vehicle's fuse box. This ensures 24/7 parking surveillance and automatic switching between ACC (Accessory) mode and parking mode, eliminating the need for a cigarette lighter adapter. The kit also incorporates smart low voltage protection to safeguard your vehicle's battery from excessive discharge.

Figure 1: Components of the Vantrue Hardwire Kit.

Setup and Installation

Proper installation of the hardwire kit is crucial for optimal performance and to prevent battery drain. Please follow these steps carefully:

1. Identify Rated Power Fuse: Locate your vehicle's fuse panel. Identify a fuse that provides constant power (remains energized even when the ignition is off). This is typically a fuse for appliances like the sun roof, power seats, or radio. Consult your car's fuse diagram (often found on the fuse panel cover or in the owner's manual) to identify suitable circuits.


Figure 2: Hardwire Kit Installation Steps.

2. Connect Hot Circuit (Red Wire): Using pliers, carefully remove the identified constant power fuse from your vehicle's fuse panel. Insert this fuse into the free slot of the provided Add-A-Circuit fuse holder. Then, insert the provided 5A fuse into the other slot of the Add-A-Circuit fuse holder. Connect the red wire from the hardwire kit to this completed Add-A-Circuit fuse holder. Finally, insert the Add-A-Circuit fuse holder back into the original fuse slot in your vehicle's fuse box.
3. Locate ACC Fuse (Yellow Wire): Identify an ACC (Accessory) fuse in your vehicle's fuse panel. This is a circuit that receives power only when the ignition is on. Consult your car's fuse diagram to find the appropriate ACC fuse.
4. Connect ACC Circuit (Yellow Wire): Remove the ACC fuse from your vehicle's fuse panel. Insert this fuse into the free slot of another Add-A-Circuit fuse holder. Connect the yellow wire from the hardwire kit to this completed Add-A-Circuit fuse holder. Insert the Add-A-Circuit fuse holder back into the original ACC fuse slot.
5. Ground Connection (Black Wire): Locate a metal bolt or screw connected to your car's metal body, preferably close to the fuse box. Loosen the screw, attach the black ground wire from the hardwire kit securely under it, and then tighten the screw. Ensure a good metal-to-metal contact for proper grounding.
6. Set Low Voltage Protection: On the hardwire kit's control box, set the low voltage protection switch to the appropriate voltage for your vehicle (e.g., 12V for 12V vehicles). It is recommended to set it to the higher voltage option (e.g., 12V) to prevent excessive battery drain, which could lead to starting issues.


Figure 3: Low Voltage Protection Settings on the Control Box.

7. Connect to Dash Cam: Route the USB-C cable from the hardwire kit to your dash cam. Plug the USB-C end into the corresponding port on your Vantrue dash cam.


Figure 4: Wire Connection Diagram.

Operating Modes

• ACC Functionality: When your vehicle's engine is ignited, the dash cam will automatically power on and operate in normal recording mode. When the engine is turned off, the hardwire kit will automatically switch the dash cam into parking mode.
• 24/7 Parking Surveillance: With the hardwire kit installed, your dash cam will receive continuous power directly from the battery, enabling 24/7 parking surveillance. This feature helps protect your vehicle against theft and provides incident recording while parked.

Maintenance

To ensure the longevity and optimal performance of your Vantrue Hardwire Kit and connected dash cam, consider the following:

• Periodically check all connections to ensure they remain secure.
• Keep the control box and wiring free from excessive dust or moisture.
• Ensure your vehicle's battery is in good condition, especially if utilizing parking surveillance for extended periods.

Troubleshooting

• Dash Cam Not Turning On/Off with Ignition:
  • Verify that the yellow ACC wire is connected to a fuse that is only active when the ignition is on.
  • Ensure the red wire is connected to a constant power source.
  • Check all fuse connections for proper insertion and contact.
• Battery Drain Issues:
  • Confirm the low voltage protection switch on the control box is set to 12V (or 24V for 24V vehicles) to prevent over-discharge.
  • If your car is not driven for extended periods (e.g., 2 days), the parking sensor might still drain the battery. Consider adjusting parking mode settings or disconnecting if not needed.
• Incompatibility with Dash Cam:
  • The hardwire kit is compatible with all Type C dash cams, including Vantrue N5, N4, N4 Pro, and other specified models. Ensure your dash cam uses a Type C USB port.
• Radio Interference:
  • The hardwire kit is designed not to interfere with radio reception. If interference occurs, check for proper grounding and secure connections.

Specifications

Warranty and Support

VANTRUE offers an 18-Month Extended Warranty for this product. They also provide a 30-Day Return Policy and 24-Hour Customer Support.

For customer support, you can reach out via:

• Email: support@vantrue.net
• Phone: 510-666-4086

The product is sold by VANTRUE and fulfilled by Amazon.