FITHOOD Battery Replacement Instruction Manual

1. Introduction

This manual provides essential instructions for the safe and effective use of your FITHOOD replacement battery. This battery is designed to replace the original battery in various Educator transmitter models.

Compatible Transmitter Models:

• Educator ET-400 Transmitters
• Educator K9-802 Transmitters
• Educator PE-900 Transmitters
• Educator ET-802 Transmitters
• Educator ET-800 Transmitters
• Educator K9-800 Transmitters

Compatible Battery Part Number: PL-752544

2. Safety Information

Please read and adhere to all safety warnings to prevent damage to the battery, device, or personal injury.

• CAUTION: Warranty void if label is removed.
• DO NOT attempt to disassemble, open, or service the battery pack.
• Replace only with the battery pack designated for this product.
• DO NOT crush, puncture, short external contacts, or dispose of in fire or water.
• DO NOT store above 60°C (140°F).
• Limited Charge Voltage: 4.2V ± 0.05V.
• Keep out of reach of children.
• Dispose of used batteries responsibly according to local regulations.

3. Product Overview

The FITHOOD replacement battery is a high-quality Li-Polymer battery designed for specific Educator transmitter models. It provides reliable power with a capacity of 700mAh.

Figure 3.1: Front view of the FITHOOD PL-752544 replacement battery, showing its blue casing, white label with specifications and warnings, and attached red and black wires with a white connector.

Figure 3.2: Angled view of the FITHOOD PL-752544 battery, highlighting the side profile and the wiring connection point.

Figure 3.3: Top-down view of the FITHOOD PL-752544 battery, clearly showing the label with model number CS-DET400SL, part number PL-752544, rating 3.7VDC, 700mAh/2.59Wh, and safety warnings.

Figure 3.4: Close-up view of the white two-pin connector attached to the red and black wires of the battery, essential for connecting to the device.

4. Installation

Battery replacement should be performed by individuals with appropriate technical knowledge. Refer to your device's specific service manual for detailed instructions on opening the device and accessing the battery compartment.

1. Power Off Device: Ensure the transmitter is completely powered off and disconnected from any power source.
2. Access Battery Compartment: Carefully open the device casing to access the internal battery. This may require specific tools and techniques depending on the transmitter model.
3. Disconnect Old Battery: Gently disconnect the old battery's connector from the device's circuit board. Note the orientation of the connector.
4. Remove Old Battery: Carefully remove the old battery from its compartment.
5. Insert New Battery: Place the new FITHOOD replacement battery into the compartment, ensuring it fits correctly without bending or forcing.
6. Connect New Battery: Connect the new battery's connector to the device's circuit board, matching the orientation of the old battery. Ensure a secure connection.
7. Secure Casing: Carefully reassemble the device casing, ensuring all screws and clips are properly secured.
8. Initial Charge: After installation, fully charge the device before its first use.

Important: Always verify that both the model and battery part number match your device before attempting installation. If unsure, consult a professional or contact support.

5. Operating

Once the battery is installed and fully charged, the device can be operated normally. Follow the operating instructions provided with your specific Educator transmitter model.

• First Use: It is recommended to fully charge the battery before the first use to calibrate the battery meter.
• Charging: Use only the charger supplied with your Educator transmitter or a compatible charger.
• Discharge: Avoid completely draining the battery frequently, as this can reduce its overall lifespan.

6. Maintenance

Proper maintenance can extend the life of your battery.

• Storage: If storing the battery for an extended period, ensure it is charged to approximately 50-60% and stored in a cool, dry place away from direct sunlight and extreme temperatures.
• Temperature: Avoid exposing the battery to extreme heat or cold, as this can degrade performance and lifespan.
• Cleaning: Keep the battery and its contacts clean and dry.

7. Troubleshooting

If you encounter issues with your replacement battery, consider the following:

• Device Not Powering On:
  • Ensure the battery is correctly installed and the connector is secure.
  • Verify the battery is charged.
  • Confirm the battery is compatible with your specific device model.
• Battery Not Charging:
  • Check the charging cable and adapter for damage.
  • Ensure the charging port on the device is clean and free of debris.
  • Confirm the charger is compatible with your device.
• Short Battery Life:
  • Ensure the battery has been fully charged.
  • Review device usage patterns; high power consumption features will drain the battery faster.
  • Extreme temperatures can affect battery performance.

If problems persist, please contact customer support for further assistance.

8. Specifications

9. Warranty and Support

This battery is manufactured under strict quality control standards and is certified with ISO9001, RoHS, CE, UN38.3, and MSDS.

For any questions regarding compatibility, installation, or performance, please contact the seller or manufacturer for professional suggestions and support. Ensure you provide your battery details or pictures if seeking assistance.