1. Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of the TE F8217 Power Line Filter. The F8217 is designed to suppress electromagnetic interference (EMI) in electrical systems, ensuring cleaner power delivery and compliance with electromagnetic compatibility (EMC) standards. Please read this manual thoroughly before installation and retain it for future reference.
2. Safety Information
WARNING: Risk of Electric Shock!
- Always disconnect power before installing, servicing, or removing the filter.
- Installation must be performed by qualified personnel in accordance with all local and national electrical codes.
- Ensure proper grounding of the filter and connected equipment.
- Do not operate the filter if it is damaged or has exposed wiring.
- Verify voltage and current ratings of the filter match the application requirements.
Failure to follow these instructions can result in serious injury or death.
3. Setup and Installation
The F8217 Power Line Filter is designed for quick connect flange mounting. Proper installation is crucial for optimal performance and safety.
3.1 Unpacking and Inspection
Carefully unpack the filter and inspect it for any signs of physical damage. If damage is found, do not install the unit and contact your supplier.
3.2 Mounting
The filter is designed for flange mounting. Secure the filter firmly to a conductive chassis or enclosure using appropriate fasteners. Ensure good electrical contact between the filter's metal casing and the chassis for effective grounding.
Figure 1: Various configurations of the F8217 Power Line Filter. The image shows three filters, one with quick connect terminals, another with screw terminals, and a third with wire leads, illustrating the different connection options available for the F8217 series.
3.3 Electrical Connection
- Identify the input (line) and output (load) terminals on the filter.
- Connect the incoming AC power line to the input terminals of the filter.
- Connect the output terminals of the filter to the equipment requiring filtered power.
- Ensure all connections are secure and properly insulated.
- Verify that the filter's ground terminal (typically the metal casing) is securely connected to the system's protective earth ground.
Refer to the wiring diagram provided with your specific filter variant for detailed connection instructions.
4. Operating Instructions
The F8217 Power Line Filter is a passive component and does not require active operation. Once correctly installed and connected, it continuously filters electromagnetic interference from the power line.
- Ensure the power supply to the filter and connected equipment is within the specified voltage and current ratings.
- The filter operates automatically to suppress common mode and differential mode noise.
5. Maintenance
The F8217 Power Line Filter is designed for maintenance-free operation under normal conditions. However, periodic inspection is recommended.
- Visual Inspection: Periodically check the filter for any signs of physical damage, corrosion, or loose connections.
- Cleaning: If necessary, gently clean the exterior of the filter with a dry, lint-free cloth. Do not use liquid cleaners or solvents.
- Connection Integrity: Ensure all electrical connections remain tight and secure.
WARNING: Disconnect power before performing any inspection or cleaning.
6. Troubleshooting
If you experience issues with your electrical system after installing the F8217 filter, consider the following common troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Equipment not powering on after filter installation. | Incorrect wiring; loose connections; filter damage. | Verify wiring against diagram. Check all connections for tightness. Inspect filter for damage. |
| EMI/Noise issues persist. | Improper grounding; filter rating insufficient; external noise source. | Ensure proper grounding. Verify filter specifications match application needs. Identify and mitigate other noise sources. |
| Filter becomes excessively hot. | Overcurrent; faulty filter. | Immediately disconnect power. Verify current draw is within filter ratings. Replace filter if faulty. |
If the problem persists after attempting these steps, contact qualified service personnel.
7. Specifications
The following are the general specifications for the TE F8217 Power Line Filter. Specific characteristics may vary slightly based on the exact variant.
- Model Number: F8217
- Rated Current: 12A
- Rated Voltage: 250VAC
- Frequency: 50Hz/60Hz
- Mounting Type: Flange Mount
- Connection Type: Quick Connect (other variants may exist)
- Manufacturer: TE Connectivity
- First Available: January 6, 2020
8. Warranty and Support
TE Connectivity products are manufactured to high-quality standards. For information regarding warranty terms, technical support, or service, please refer to the official TE Connectivity website or contact their customer service directly.
Note: This manual is for informational purposes only and does not constitute a warranty.