SICCOO 14-Bulb RGB Colorful DIY Hollywood Makeup Vanity Mirror Dimmable Lights Instruction Manual

Important Safety Information

Please read all instructions carefully before installation and use. Retain this manual for future reference.

• This product is designed for indoor use only.
• Ensure the power source is 5V USB. Using an incorrect voltage may damage the product and pose a safety risk.
• The bulbs are crafted with ABS fireproof materials and remain cool to the touch, enhancing safety for users, children, and pets.
• Do not immerse the product in water or expose it to excessive moisture.
• Keep the product away from heat sources and direct sunlight.
• Do not attempt to disassemble or modify the product. This will void the warranty and may cause damage or injury.

Package Contents

Verify that all components are present in the package:

• 1 x Vanity Lights Kit with 14 bulbs
• 1 x Spare double-sided tape set
• 1 x English instruction manual (this document)

Product Overview

The SICCOO 14-Bulb RGB Colorful DIY Hollywood Makeup Vanity Mirror Dimmable Lights provide versatile illumination for various applications. These lights feature both warm and daylight white dimmable options, along with 16 RGB colorful lighting modes. The USB-powered design ensures convenience and safety.

Setup Instructions

Follow these steps to install your vanity lights:

1. Prepare the Surface: Ensure the mirror or surface where the lights will be installed is clean, dry, and free of dust or grease.
2. Plan Layout: Determine the desired spacing and arrangement of the bulbs on your mirror. The cable length between bulbs can be adjusted by rotating the bulb bases to wind or unwind excess cable. Refer to the dimension diagram for typical spacing.
3. Attach Adhesive: Peel off one side of the double-sided adhesive tape and apply it firmly to the base of each bulb.
4. Install Bulbs: Carefully peel off the other side of the adhesive tape and press each bulb firmly onto the desired position on your mirror. Hold each bulb in place for a few seconds to ensure a strong bond.
5. Connect Power: Plug the USB connector into a compatible 5V USB power source, such as a USB wall plug, power bank, or PC.

Operating Instructions

The vanity lights are controlled via an inline remote. Refer to the diagram below for button functions.

• Power On/Off: Press the circular button (power icon) to turn the lights on or off.
• White Light Brightness Adjustment: Long press the button labeled 'W' to adjust the brightness of the white light.
• Warm/Daylight White Regulation: Long press the top button (likely 'M+' or a dedicated button for warm light) for warm light regulation. Long press the bottom button (likely 'M-' or a dedicated button for daylight white) for daylight white regulation.
• RGB Color Modes: Press the button labeled 'RGB' to cycle through the 16 different colorful lighting modes. Use the 'M+' and 'M-' buttons to navigate between dynamic display and scene light modes.
• USB Charging Port: An additional USB port is integrated into the controller for charging your phone or other small devices.

Maintenance

Proper maintenance ensures the longevity and optimal performance of your vanity lights.

• Cleaning: Disconnect the power before cleaning. Use a soft, dry cloth to gently wipe the bulbs and cables. Do not use abrasive cleaners or solvents.
• Storage: If storing the lights for an extended period, ensure they are clean and dry. Store them in a cool, dry place away from direct sunlight and extreme temperatures.
• Adhesive Care: If the adhesive pads lose their stickiness over time, use the provided spare double-sided tape for re-installation.

Troubleshooting

If you encounter issues with your vanity lights, refer to the following common problems and solutions:

• Lights not turning on:
  • Ensure the USB power source is properly connected and functioning.
  • Verify that the power button on the inline controller has been pressed.
  • Try connecting to a different USB power source.
• Lights flickering:
  • Ensure the USB power source provides stable power.
  • Check for loose connections in the USB cable or controller.
• Adhesive not holding:
  • Ensure the surface was clean and dry before application.
  • Apply new double-sided tape from the spare set provided.
  • Press firmly for an extended period during installation.
• Colors not changing or brightness not adjusting:
  • Ensure you are using the correct buttons on the inline controller as described in the Operating Instructions.
  • Disconnect and reconnect the USB power to reset the controller.

Specifications

Warranty and Support

For warranty information or technical support, please contact SICCOO customer service through the retailer where the product was purchased or refer to the official SICCOO website. Please have your model number and purchase date available when contacting support.