Fitkit by Cult FT98 Carbon Treadmill User Manual

1. Setup and Installation

This section guides you through the unboxing and initial assembly of your Fitkit by Cult FT98 Carbon Treadmill. Ensure all components are present before beginning.

1.1 Unboxing and Component Check

Carefully cut and open the treadmill box. Remove all packaging materials. Verify that the following items are included in your installation kit:

• User's Manual
• Warranty Card
• Safety Key
• Screws (various sizes)
• Lubrication Oil
• Allen Keys
• Screwdriver with Spanner

Image: All components of the Fitkit FT98 Carbon Treadmill laid out for assembly.

1.2 Assembly Steps

Follow these steps to assemble your treadmill:

1. Lift the Upright Column: Carefully lift the upright column of the treadmill into its vertical position.
2. Attach Small Screws: Secure the upright column by attaching the two small screws on both sides at the base. Tighten them clockwise using the provided Allen key.
3. Attach Big Screws: Insert the two larger screws on both sides of the upright column and tighten them clockwise using the provided Allen key.
4. Fix the Console: Loosen the screws on both sides of the console attachment points by rotating them anti-clockwise with the Allen key. Position the console and then fix it by inserting and tightening the big screws clockwise on both sides.
5. Clip Side Covers: Attach the decorative side covers to conceal the screw points at the base of the upright column.
6. Place Safety Key: Insert the red safety key into its designated slot on the console. This is crucial for the treadmill to operate.
7. Turn On Power: Connect the power cord and turn on the main power switch, usually located at the front base of the treadmill.

2. Operating Instructions

Understand how to safely and effectively use your treadmill for your fitness routine.

2.1 Safety Precautions

• Always wear proper athletic shoes when using the treadmill. Avoid going barefoot.
• Ensure the safety key is correctly placed before starting any workout.
• Do not step on the running belt until it has started moving at a slow speed.
• Hold onto the handrails for balance, especially when starting or stopping.

2.2 Console Functions

The LED display console provides essential workout information and controls:

Image: Close-up of the LED display console with control buttons.

• Display: Shows speed, time, distance, and calories burned.
• Start/Stop: Press to begin or end your workout.
• Speed +/-: Adjust the running belt speed.
• Mode: Cycle through different display modes or workout programs.
• PROG: Select pre-set workout programs.

2.3 Starting a Workout

1. Ensure the treadmill is plugged in and the power switch is ON.
2. Attach the safety key to your clothing and place it in the console slot.
3. Stand on the side rails, not on the running belt.
4. Press the 'Start' button. The belt will begin to move slowly.
5. Carefully step onto the moving belt and adjust the speed to your desired level using the 'Speed +/-' buttons.

Image: A user demonstrating proper form while exercising on the treadmill.

3. Maintenance

Regular maintenance ensures the longevity and optimal performance of your treadmill.

3.1 Lubrication

The Fitkit FT98 Carbon Treadmill features easy lubrication. Apply the provided lubrication oil under the running belt periodically as instructed in the detailed user manual to reduce friction and wear.

3.2 Cleaning

• Wipe down the console and handrails with a damp cloth after each use to remove sweat and dust.
• Periodically vacuum under the treadmill to prevent dust and debris from accumulating in the motor area.
• Ensure the running belt is clean and free of debris. The anti-skid surface is designed for durability, but regular cleaning helps maintain its grip.

Image: The anti-skid surface of the running belt, designed for user safety and grip.

3.3 Belt Adjustment

If the running belt feels loose, slips, or is off-center, refer to the detailed user manual for instructions on how to adjust the belt tension and alignment using the provided tools.

4. Troubleshooting

This section addresses common issues you might encounter with your treadmill.

4.1 Common Issues and Solutions

• Treadmill Not Starting:
  • Check if the power cord is securely plugged into a grounded outlet.
  • Ensure the main power switch at the base of the treadmill is ON.
  • Verify that the safety key is correctly placed in the console slot.
  • Confirm that the circuit breaker has not tripped.
• Running Belt Slipping or Hesitating:
  • The running belt may require lubrication. Refer to Section 3.1.
  • The running belt may need tension adjustment. Refer to Section 3.3.
• Unusual Noises:
  • Check for any loose screws or parts and tighten them.
  • Ensure the treadmill is on a flat, stable surface.
  • If the noise persists, it may indicate an internal issue. Contact customer support.

For any issues not covered here or if problems persist, please contact customer support for assistance.

5. Specifications

Detailed technical specifications for the Fitkit by Cult FT98 Carbon Treadmill.

Image: Technical specifications and dimensions of the Fitkit FT98 Carbon Treadmill.

6. Warranty Information

Your Fitkit by Cult FT98 Carbon Treadmill comes with the following warranty:

• Motor: 1 Year manufacturer warranty.
• Manufacturing Defect: 1 Year manufacturer warranty.
• Frame: 3 Year warranty.

Please retain your Warranty Card and invoice copy for any service claims. Warranty validity will be calculated from the date of invoice.

7. Customer Support

For installation support, technical assistance, or any queries regarding your treadmill, please contact our customer support team.

7.1 Contact Information

• Toll-Free Numbers: 1800-572-6303 / 1800-572-6402
• Email: info@cultsport.com
• Website: www.cultsport.com
• WhatsApp Numbers: +91-6260741911, +91-6260741910

7.2 Support Hours

Customer support is available Monday to Sunday, from 9 AM to 6 PM. Service schedules may vary by location.