Introduction
This instruction manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Avantco WB8L 2.1 Gallon (8 Liter) Water Boiler. Please read this manual thoroughly before initial use and retain it for future reference. This appliance is designed for commercial use to heat and dispense hot water.
Important Safety Information
WARNING: To reduce the risk of fire, electric shock, or injury, always follow basic safety precautions when using electrical appliances.
- Read all instructions before operating the appliance.
- Ensure the appliance is connected to a properly grounded 120V, 1500W electrical outlet. Do not use extension cords.
- Do not immerse the appliance, cord, or plug in water or other liquids.
- Always unplug the appliance from the outlet when not in use, before cleaning, or before attempting any maintenance.
- Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner.
- Keep hands and face away from the steam vent and dispensing spout during operation, as hot steam and water can cause severe burns.
- Place the appliance on a stable, level, heat-resistant surface, away from walls and combustible materials.
- Do not allow the cord to hang over the edge of a table or counter, or touch hot surfaces.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Setup
- Unpacking: Carefully remove the water boiler from its packaging. Retain packaging for future storage or shipping.
- Initial Cleaning: Before first use, wash the interior of the boiler and the lid with warm, soapy water. Rinse thoroughly with clean water. Wipe the exterior with a damp cloth.
- Placement: Place the water boiler on a stable, level, and heat-resistant surface. Ensure there is adequate clearance around the unit for ventilation and to prevent heat damage to surrounding surfaces. Do not place near flammable materials.
- Power Connection: Ensure the power switch is in the 'OFF' position. Plug the power cord into a grounded 120V, 1500W electrical outlet.
Image: Front view of the Avantco WB8L Water Boiler, showing the water level indicator and dispensing spigot.
Image: Back view of the Avantco WB8L Water Boiler, showing the power cord, temperature control dial, and power switch.
Operating Instructions
- Filling the Boiler: Remove the lid and fill the boiler with cold water. Do not fill above the 'MAX' line indicated on the water level gauge. Ensure the lid is securely replaced after filling.
- Powering On: Turn the power switch to the 'ON' position. The 'Heating' indicator light will illuminate, signifying that the water is beginning to heat.
- Heating Process: The 1500W heating element provides rapid boiling. The water will heat to the desired temperature set by the temperature control dial. Once the water reaches the set temperature, the 'Heating' light may cycle on and off to maintain the temperature.
- Temperature Control: Use the temperature control dial located on the back of the unit to adjust the desired water temperature. Turn clockwise to increase temperature, counter-clockwise to decrease.
- Dispensing Hot Water: To dispense hot water, place a cup or container under the dispensing spigot and push the lever down. Release the lever to stop the flow of water.
- Keep Warm Function: The unit is designed to maintain the water at the set temperature once it has reached boiling point, ensuring hot water is always available. The 'Keep Warm' indicator light will illuminate when this function is active.
- Powering Off: When finished, turn the power switch to the 'OFF' position and unplug the unit from the electrical outlet. Allow the unit to cool completely before handling or cleaning.
Image: The Avantco WB8L Water Boiler positioned on a counter, ready for use, with a cup nearby.
Maintenance and Cleaning
Regular cleaning and maintenance will ensure the longevity and optimal performance of your water boiler.
- Daily Cleaning: After each use, ensure the unit is unplugged and completely cool. Empty any remaining water. Wipe the exterior with a damp cloth. Clean the drip tray if present.
- Interior Cleaning: For the interior, the product care instructions state "Hand wash, Wipe clean". Use warm, soapy water and a soft brush or sponge to clean the inside. Rinse thoroughly.
- Descaling: Mineral deposits (limescale) can build up over time, especially in hard water areas, affecting performance. Descale the unit regularly (e.g., monthly or as needed based on water hardness).
To descale: Fill the boiler with a solution of equal parts white vinegar and water. Let it sit for 30-60 minutes (do not heat). For heavy buildup, you may gently heat the solution for a short period (do not boil dry). Drain the solution and rinse the interior thoroughly several times with fresh water to remove any vinegar residue. - Spigot Cleaning: Ensure the dispensing spigot is free of blockages. If necessary, disassemble and clean according to manufacturer guidelines (if applicable).
- Storage: When not in use for extended periods, ensure the unit is clean, dry, and stored in a cool, dry place.
Troubleshooting
If you encounter issues with your Avantco WB8L Water Boiler, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not heat or power on. | Not plugged in; Power switch off; No power at outlet; Circuit breaker tripped. | Ensure unit is securely plugged in; Turn power switch to 'ON'; Check outlet with another appliance; Reset circuit breaker. |
| Water heats slowly or not to desired temperature. | Limescale buildup; Temperature dial set too low. | Perform descaling procedure; Adjust temperature dial to a higher setting. |
| Water leaks from spigot. | Spigot not fully closed; Spigot seal worn or damaged. | Ensure spigot lever is fully released; Contact customer support for replacement parts if seal is damaged. |
| Water level gauge is unclear. | Mineral deposits on gauge. | Perform descaling procedure. |
Specifications
- Model: WB8L
- Capacity: 2.1 Gallons (8 Liters)
- Voltage: 120V
- Wattage: 1500W
- Color: Silver
- Special Feature: Rapid Boil
- Product Care Instructions: Hand wash, Wipe clean
Warranty and Support
For information regarding the warranty of your Avantco WB8L Water Boiler, please refer to the warranty card included with your purchase or contact the retailer or manufacturer directly. Warranty terms and conditions may vary.
For technical support, replacement parts, or service inquiries, please contact Avantco customer service. Contact information can typically be found on the manufacturer's website or on the product packaging.
