SEBSON IR_OUT_E
Contents
SEBSON Outdoor Motion Sensor User Manual
Model: IR_OUT_E
1. Introduction
This SEBSON outdoor motion sensor is designed for reliable motion detection in various outdoor environments. Featuring two infrared sensors, it offers enhanced detection capabilities for people, large animals, and vehicles. Its robust IP65 rating ensures durability against outdoor elements. The sensor is programmable for light duration and ambient brightness, making it a versatile solution for automated lighting control.
2. Key Features
- Outdoor Use & IP65 Rating: Designed for outdoor installation with high protection against dust and water jets.
- Dual Infrared Sensors: Equipped with two PIR sensors for improved detection coverage, including forward, backward, and directly below the sensor.
- Wide Detection Range: Detects motion up to 12 meters at a 180° angle and up to 3 meters at a 360° angle (on a free surface).
- Adjustable Light Duration: Programmable shut-off time from approximately 10 seconds to 15 minutes.
- Adjustable Ambient Brightness (LUX): Sensitivity to ambient light can be set between 3 and 2000 Lux, allowing operation only when needed (e.g., only at night).
- Vertical Rotation: The sensor head can be rotated 180° vertically to fine-tune the detection area.
- High Load Capacity: Supports up to 1200W for incandescent lamps and up to 600W for LED and energy-saving lamps.
- Easy Installation: Surface and wall mountable with 3-wire connection.
3. Product Specifications
| Specification | Value |
|---|---|
| Operating Voltage | 220-240V AC 50/60Hz |
| Max. Power Consumption (Incandescent) | 1200W |
| Max. Power Consumption (LED/Energy-saving) | 600W |
| Standby Power Consumption | 0.5W |
| Detection Speed | 0.6-1.5 m/s |
| Detection Range (180°) | Max. 12m (<24°C) |
| Detection Range (360°) | Max. 3m (<24°C) |
| Ambient Brightness (LUX) | 3-2000 Lux |
| Protection Rating | IP65 |
| Shut-off Time | Min. 10s (±3s) - Max. 15min (±2min) |
| Ambient Temperature | -20°C to +40°C |
| Humidity | <93% |
| Vertical Rotation | 180° |
| Dimensions (L x W x H) | 90 x 74 x 40 mm |
| Housing Material | Plastic |
| Model Number | IR_OUT_E |
4. Setup and Installation
The SEBSON motion sensor is designed for surface and wall mounting. Ensure the power supply is disconnected before beginning installation.
4.1 Mounting Location
Choose a stable wall or surface for mounting. Consider the desired detection area and avoid obstructions. The sensor can be rotated 180° vertically to fine-tune the detection zone after mounting.

Image: Dimensional drawing showing the sensor's height (90mm), width (74mm), and depth (40mm), along with its 180-degree vertical rotation capability.
4.2 Wiring
This sensor requires a 3-wire connection (Live, Neutral, Switched Live to load). Consult a qualified electrician for wiring if you are unsure. Ensure all connections are secure and insulated.

Image: Rear view of the motion sensor, illustrating the mounting holes and the access point for electrical wiring.
5. Operating Instructions
Once installed and powered, the motion sensor will automatically detect movement and activate the connected lighting or device based on its settings.
5.1 Adjusting Settings (LUX and TIME)
The sensor features two adjustable dials for customizing its operation:
- LUX (Ambient Brightness): This dial controls the ambient light level at which the sensor becomes active.
- Turn towards the sun icon (2000 Lux) for the sensor to operate during both day and night.
- Turn towards the moon icon (3 Lux) for the sensor to operate only in low light conditions (e.g., at dusk or night).
- TIME (Shut-off Duration): This dial sets how long the connected light/device remains on after motion is detected and no further motion is sensed.
- Adjust from a minimum of 10 seconds to a maximum of 15 minutes.

Image: A detailed view of the two rotary dials on the sensor, labeled 'LUX' and 'TIME', used for adjusting ambient light sensitivity and the duration of activation.

Image: Diagram illustrating the motion sensor's detection range (12m at 180 degrees, 3m at 360 degrees) and a visual representation of the TIME and LUX dial settings.
6. Maintenance
The SEBSON motion sensor is designed for low maintenance. Regular cleaning and inspection will ensure optimal performance.
- Cleaning: Gently wipe the sensor lens and housing with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the plastic and sensor components.
- Inspection: Periodically check the mounting for stability and ensure no debris (e.g., leaves, spiderwebs) is obstructing the sensor's view.
- Wiring: Ensure wiring connections remain secure and free from corrosion.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on when motion is detected. |
|
|
| Light stays on too long or turns on randomly. |
|
|
| Detection range is shorter than expected. |
|
|
8. Warranty and Support
This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and duration. For technical support, troubleshooting assistance, or warranty claims, please contact SEBSON customer service through their official website or the retailer from whom you purchased the product.
Note: The product description mentions "Instruction manual (English language not guaranteed)". This manual provides general guidance. For detailed technical support, always refer to the official SEBSON support channels.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.