SVS SB-2000 Pro DSP Controlled 12" Sealed Subwoofer User Manual

1. Introduction

This manual provides comprehensive instructions for the setup, operation, and maintenance of your SVS SB-2000 Pro DSP Controlled 12" Sealed Subwoofer. Please read this manual thoroughly before operating your subwoofer to ensure optimal performance and longevity.

The SVS SB-2000 Pro delivers jaw-dropping deep bass extension and massive output with stunning musicality, designed to enhance both audiophile music listening and home theater experiences.

2. Key Features

• All-new 12-inch SVS high-excursion driver for powerful and accurate bass.
• 550 Watts RMS, 1,500+ Watts peak power Sledge amplifier with fully discrete MOSFET output.
• SVS subwoofer DSP smartphone app for advanced control and custom presets.
• Compact sealed cabinet design for tight, musical bass.
• Robust construction with premium black ash finish.

3. Setup and Installation

3.1 Unpacking

Carefully remove the subwoofer from its packaging. Inspect for any signs of damage during transit. Retain all packaging materials for future transport or service needs.

3.2 Placement

Subwoofer placement significantly impacts sound quality. Experiment with different locations to find the best bass response in your listening area. Common placements include:

• Front of Room: Near the main speakers, often in a corner for maximum output.
• Mid-Wall: Along a side wall, which can provide a smoother bass response.
• Multiple Subwoofers: For optimal room coverage and smoother bass, consider using two or more subwoofers.

Figure 1: Front view of the SVS SB-2000 Pro Subwoofer, showcasing the 12-inch driver.

Figure 2: Front view of the SVS SB-2000 Pro Subwoofer with the protective grille attached.

3.3 Connections

Ensure all audio components are powered off before making connections. The SB-2000 Pro offers various connection options:

• LFE Input (Recommended): Connect a single RCA cable from your AV receiver's LFE or Subwoofer Pre-Out to the LFE input on the subwoofer.
• Stereo RCA Inputs: For stereo pre-amplifiers or processors, connect left and right RCA outputs to the corresponding Line Level inputs on the subwoofer.
• Speaker Level Inputs: If your receiver does not have RCA pre-outs, connect speaker wires from your amplifier's main speaker outputs to the subwoofer's speaker level inputs.

Figure 3: Rear panel of the SVS SB-2000 Pro Subwoofer, showing the various input and control options.

After making connections, plug the power cord into the subwoofer and then into a wall outlet. The subwoofer features an auto-on/standby mode.

4. Operation

4.1 SVS Subwoofer DSP Smartphone App

The SVS SB-2000 Pro can be fully controlled via the SVS Subwoofer DSP smartphone app, available for iOS and Android devices. This app allows for convenient adjustment of all DSP functions from your listening position.

• Volume Control: Adjust the overall output level.
• Low Pass Filter: Set the crossover frequency to blend the subwoofer with your main speakers.
• Phase Control: Adjust the phase to ensure bass waves from the subwoofer align with your main speakers.
• Parametric EQ: Fine-tune the frequency response to compensate for room acoustics.
• Room Gain Compensation: Adjust for excessive bass output in smaller rooms.
• User Presets: Save custom settings for different listening modes (e.g., Music, Movies).

4.2 Manual Controls

Basic controls are also available on the rear panel, including volume, phase, and low pass filter. However, the app provides more precise and comprehensive control.

5. Maintenance

To maintain the appearance and performance of your SVS SB-2000 Pro Subwoofer:

• Wipe the cabinet with a soft, dry cloth. Avoid abrasive cleaners or solvents.
• Do not expose the subwoofer to excessive moisture, heat, or direct sunlight.
• Ensure adequate ventilation around the amplifier panel.

6. Troubleshooting

If you experience issues with your subwoofer, refer to the following common solutions:

• No Sound: Check power connections, ensure the subwoofer is turned on, verify audio cable connections, and check the volume settings on both the subwoofer and your receiver.
• Distorted Sound: Reduce the volume, check for loose connections, and ensure the low pass filter and phase settings are correctly configured.
• Humming Noise: This can often be caused by a ground loop. Try connecting the subwoofer to a different electrical outlet, or use a ground loop isolator.
• Subwoofer Not Turning On/Off Automatically: Adjust the auto-on sensitivity setting in the SVS app or on the rear panel.

For persistent issues, contact SVS customer support.

7. Specifications

Figure 4: Dimensions of the SVS SB-2000 Pro Subwoofer.

8. Warranty and Support

The SVS SB-2000 Pro Subwoofer comes with a limited warranty. For detailed warranty information, terms, and conditions, please refer to the official SVS website or contact SVS customer support directly.

For technical assistance, troubleshooting, or service inquiries, please visit the SVS support page or contact their customer service team. Contact information can be found on the official SVS website: www.svsound.com