YONGJIANGXIA KCE-422i iPod/iPhone Connection Cable Instruction Manual

1. Introduction

The YONGJIANGXIA KCE-422i cable provides a direct connection solution for integrating your Apple iPod or iPhone with compatible Alpine car stereo head units manufactured from 2006 onwards. This cable enables control of your Apple device directly from the head unit, allowing you to enjoy your music through your car's speakers while simultaneously charging the device.

This manual provides instructions for the proper installation and use of your KCE-422i cable.

2. Setup and Installation

Before installation, ensure your Alpine head unit is compatible with the KCE-422i adapter. Refer to your Alpine head unit's user manual for confirmation of "Aux. input option using a KCE-422I adapter."

1. Power Off: Turn off your car's ignition and disconnect the car battery to prevent electrical damage during installation.
2. Locate Alpine Head Unit Port: Identify the "D-shaped" 10-pin DIN port on the back of your compatible Alpine head unit. This port is typically labeled for auxiliary input or iPod connection.
3. Connect DIN Plug: Carefully insert the 10-pin DIN plug of the KCE-422i cable into the corresponding port on the Alpine head unit. Ensure a secure and firm connection.
4. Route Cable: Route the cable to a convenient location within your vehicle where your iPod or iPhone will be placed. Avoid routing the cable near moving parts or heat sources.
5. Connect iPod/iPhone: Plug the iPod/iPhone dock connector end of the KCE-422i cable into your Apple device.
6. Reconnect Power: Reconnect your car battery and turn on the ignition.

Figure 1: The 10-pin DIN connector of the KCE-422i cable, designed for connection to compatible Alpine head units.

Figure 2: The complete KCE-422i cable, illustrating both the Alpine DIN connector and the Apple iPod/iPhone dock connector.

3. Operating Instructions

Once the KCE-422i cable is connected and your Apple device is plugged in, you can operate your iPod/iPhone through your Alpine head unit.

• Source Selection: On your Alpine head unit, select the appropriate source input for the iPod/iPhone (e.g., "iPod," "Aux," or "Full Speed"). Refer to your head unit's manual for specific source selection steps.
• Music Playback: You can browse and select music by artist, album, song, or playlist directly from your Alpine head unit's controls.
• Information Display: Artist, album, song title, and playlist information will be displayed on the head unit's screen.
• Charging: The KCE-422i cable will automatically charge your connected iPod or iPhone while it is plugged in and the head unit is powered on.

4. Compatible Alpine Head Units

The KCE-422i cable is compatible with the following Alpine head units (2006-up Full Speed-compatible models):

• CDA-9852/E
• CDA-9856/E
• CDA-9857/E
• CDE-9870/E/R/RM
• CDE-9871/R/RR
• CDE-9873/E/RB
• CDE-9881/R/RB
• CDA-9883/E/R
• CDE-9885/R
• CDE-9887/R
• DVA-9861/Ri
• IVA-D105/E/R
• IDA-X001
• IVA-W205/E
• IVA-W202R
• IVA-W200Ri
• IDA-X001

Note: This list may not be exhaustive. Always verify compatibility with your specific Alpine head unit's documentation.

5. Maintenance

To ensure the longevity and optimal performance of your KCE-422i cable, follow these simple maintenance guidelines:

• Handle with Care: Avoid excessive bending, twisting, or pulling on the cable, especially near the connectors.
• Keep Clean: Periodically wipe the cable and connectors with a soft, dry cloth to remove dust and debris. Do not use harsh chemicals or abrasive cleaners.
• Avoid Extreme Conditions: Protect the cable from extreme temperatures, direct sunlight, and moisture.
• Proper Storage: When not in use, store the cable in a clean, dry place, ideally coiled loosely to prevent kinks.

6. Troubleshooting

If you encounter issues with your KCE-422i cable, try the following troubleshooting steps:

• No Audio/Device Not Recognized:
  • Ensure both ends of the cable are securely connected to the Alpine head unit and your Apple device.
  • Verify that the correct source input is selected on your Alpine head unit.
  • Restart your Apple device.
  • Check your Alpine head unit's manual to confirm KCE-422i compatibility and proper setup.
  • Test with a different compatible Apple device, if available, to rule out device-specific issues.
• Device Not Charging:
  • Confirm the cable is fully plugged into both the head unit and the Apple device.
  • Ensure the Alpine head unit is powered on.
  • Check for any debris or damage in the charging port of your Apple device or the cable's connector.
• Intermittent Connection:
  • Inspect the cable for any visible damage, such as cuts or frayed wires.
  • Ensure connectors are clean and free of corrosion.
  • Avoid placing strain on the cable during use.

If problems persist after attempting these steps, contact customer support for further assistance.

7. Specifications

8. Warranty and Support

For warranty information or technical support regarding your YONGJIANGXIA KCE-422i cable, please refer to the documentation provided at the time of purchase or contact the seller directly. Keep your purchase receipt as proof of purchase.

For general inquiries or further assistance, you may visit the YONGJIANGXIA Store on Amazon.