MINELAB PRO-FIND 20

Minelab PRO-FIND 20 Waterproof Pinpointer Metal Detector Instruction Manual

Brand: MINELAB | Model: PRO-FIND 20

Introduction

The Minelab PRO-FIND 20 is a waterproof pinpointer metal detector designed for precise target location. It features Detector Interference Free (DIF) technology, audio and vibration indication, and high visibility for ease of use in various environments. This manual provides essential information for setting up, operating, and maintaining your PRO-FIND 20.

Minelab PRO-FIND 20 Pinpointer

Image: The Minelab PRO-FIND 20 pinpointer, an orange and black handheld device, shown with its holster.

Safety Information

WARNING:

  • Keep product away from water beyond 5 ft (1.5 m) to prevent damage to non-waterproof components.
  • Keep batteries out of reach of children.

Package Contents

Your Minelab PRO-FIND 20 package includes:

  • Minelab PRO-FIND 20 Pinpointer
  • Belt Holster
  • User Manual (this document)

Note: A 9V PP3 battery is required for operation and is not included in the package.

Setup

1. Battery Installation

  1. Unscrew the battery cap at the rear of the pinpointer.
  2. Insert one 9V PP3 battery, ensuring correct polarity (+/-).
  3. Carefully screw the battery cap back on, ensuring the O-ring is properly seated to maintain the waterproof seal. Do not overtighten.

2. Holster Attachment

The included durable holster can be attached to any belt for easy access to your PRO-FIND 20.

Minelab PRO-FIND 20 Holster

Image: Close-up of the PRO-FIND 20 holster, showing the belt loop and snap button for secure attachment.

Operating Instructions

1. Power On/Off

  • To power on: Press and hold the power button until the device activates.
  • To power off: Press and hold the power button until the device deactivates.

2. Calibration

Upon powering on, the PRO-FIND 20 will perform an automatic calibration. Ensure the pinpointer is held away from any metal objects during this process for accurate calibration.

3. Detection Indication (Audio & Vibration)

The PRO-FIND 20 provides both audio tones and vibrations to indicate the presence of metal. As the probe approaches a target, the audio tones will intensify and the vibration will increase, helping to pinpoint the exact location.

Minelab PRO-FIND 20 Audio Indication

Image: A person using the PRO-FIND 20 to locate a target in the soil, illustrating the audio indication feature.

4. Lost Alarm

If the PRO-FIND 20 is left inactive for a period, a lost alarm will sound to help you locate it, especially useful in low light or tall grass.

5. DIF Technology

The Detector Interference Free (DIF) technology disengages the pinpointer coil's magnetic field when switched off, significantly reducing interference with an operating metal detector.

Minelab PRO-FIND 20 DIF Technology

Image: A diagram illustrating the DIF Technology chip, highlighting its role in reducing interference.

6. Waterproof Design

The PRO-FIND 20 is fully waterproof up to 5 ft (1.5 m), allowing for accurate detection of targets in shallow water environments.

Minelab PRO-FIND 20 Waterproof

Image: The PRO-FIND 20 pinpointer being used in shallow water, demonstrating its waterproof capability.

Maintenance

  • After each use, especially in wet or dirty conditions, wipe the pinpointer clean with a damp cloth.
  • Regularly inspect the battery cap O-ring for any signs of wear or damage. Replace if necessary to maintain waterproofing.
  • Store the device in a cool, dry place when not in use.

Troubleshooting

Device Not Powering On

  • Ensure the 9V PP3 battery is correctly installed with proper polarity.
  • Check if the battery has sufficient charge. Replace with a new battery if needed.
  • Verify the battery cap is securely fastened.

Inconsistent Power On Cycle

  • Ensure the pinpointer is held away from any metal objects during the power-on calibration sequence.
  • If the issue persists, try replacing the battery.

No Detection or Weak Signal

  • Ensure the battery has sufficient charge.
  • Recalibrate the device by turning it off and on again away from metal.

Specifications

FeatureDetail
BrandMINELAB
ModelPRO-FIND 20
ColorBlack
Power SourceBattery Powered (9V PP3, not included)
Item Weight6.5 oz (184 g)
Product Dimensions9.7"L (247 mm)
Waterproof RatingUp to 5 ft (1.5 m)
IndicationAudio & Vibration
TechnologyDIF (Detector Interference Free)
UPC811493016917
Item Model Number3226-0004

Warranty and Support

For warranty information and technical support, please refer to the official MINELAB website or contact MINELAB customer service directly. Protection plans may be available for extended coverage.

  • 2-Year Protection Plan (available separately)
  • 3-Year Protection Plan (available separately)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.