ANTLUX 4FT LED Wraparound 40W Shop Light Instruction Manual

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your ANTLUX 4FT LED Wraparound 40W Shop Light. Please read this manual thoroughly before installation and retain it for future reference. This LED fixture is designed for various indoor applications, offering efficient and bright illumination.

2. Safety Information

• Electrical Safety: Always disconnect power at the circuit breaker before installation, maintenance, or removal of the fixture. Ensure all wiring connections are secure and comply with local electrical codes. If you are unsure about wiring, consult a qualified electrician.
• Grounding: The fixture must be properly grounded to prevent electrical shock.
• Voltage: Verify that the supply voltage is compatible with the fixture's requirements (120 Volts).
• Handling: Handle the fixture with care. Avoid dropping or subjecting it to strong impacts.
• Environment: This fixture is designed for indoor use only. Do not expose it to moisture or extreme temperatures.
• Heat: While LED fixtures generate less heat than traditional lighting, ensure adequate ventilation around the fixture.

3. Package Contents

Upon opening the package, ensure all components are present and undamaged. The standard package includes:

• ANTLUX 4FT LED Wraparound Light Fixtures (Quantity as purchased, e.g., 4 units)
• Mounting Hardware (screws, anchors)
• Wire Nuts
• Instruction Manual

4. Specifications

Figure 1: Key specifications of the ANTLUX LED Wraparound Light.

5. Setup and Installation

The ANTLUX LED Wraparound Light is designed for easy installation. Follow these steps carefully:

1. Prepare for Installation:
   • Turn off power at the circuit breaker before beginning.
   • Unpack the fixture and inspect for any damage.
   • Gather necessary tools: screwdriver, wire strippers, drill (if mounting to drywall/ceiling joists).
2. Mounting the Fixture:
   • Position the fixture on the desired ceiling or wall location. Mark the mounting points.
   • Drill pilot holes if necessary and insert anchors for drywall mounting.
   • Secure the fixture to the mounting surface using the provided screws. Ensure it is firmly attached.
   

   Figure 2: Exploded view and installation ease.

3. Wiring Connections:
   • Connect the fixture's wires to your building's electrical wires (Live to Live, Neutral to Neutral, Ground to Ground) using the provided wire nuts. Ensure all connections are tight and secure.
   • Tuck all wires neatly into the junction box or fixture housing.
4. Linking Multiple Fixtures (Optional):
   • If linking multiple lights, locate the knock-out sections on the ends of the fixtures.
   • Carefully remove the knock-out to create an opening for connecting fixtures in a continuous line. Up to 20 fixtures can be linked.
   • Connect the wiring between linked fixtures as per electrical codes.
   

   Figure 3: Linking multiple fixtures and prismatic acrylic cover detail.

5. Restore Power: Once installation is complete and all connections are secure, restore power at the circuit breaker.

6. Operating Instructions

The ANTLUX LED Wraparound Light operates via a standard wall switch connected to its power source. Simply toggle the switch to turn the light on or off.

7. Maintenance

The ANTLUX LED Wraparound Light is designed for minimal maintenance. Follow these guidelines to ensure optimal performance and longevity:

• Cleaning: Disconnect power before cleaning. Use a soft, dry, or slightly damp cloth to wipe the exterior of the fixture. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or acrylic cover.
• Inspection: Periodically check the mounting hardware and wiring connections to ensure they remain secure.
• No User-Serviceable Parts: The LED components are integrated and not user-replaceable. Do not attempt to open or modify the fixture.

8. Troubleshooting

If you encounter issues with your ANTLUX LED Wraparound Light, refer to the following troubleshooting steps:

• Light Does Not Turn On:
  • Check the circuit breaker to ensure power is supplied to the fixture.
  • Verify that the wall switch is in the 'ON' position.
  • Ensure all wiring connections are secure and correctly made.
• Light Flickers:
  • Confirm that all wiring connections are tight and free from loose contacts.
  • Check for any faulty circuit breakers or switches that might be causing intermittent power supply.
  • Ensure the fixture is not connected to a dimmer switch unless explicitly rated for dimming, as this model is not specified as dimmable.
• Reduced Brightness:
  • Clean the acrylic cover to remove any dust or debris that may be obstructing light output.
  • Verify the power supply voltage is stable and within the specified range.

If these steps do not resolve the issue, please contact customer support.

9. Warranty and Support

ANTLUX LED Wraparound Lights are designed for long-lasting performance, with an estimated lifespan of 50,000 hours, which translates to approximately 23 years based on 6 hours of daily use.

For any support needs, questions, or concerns regarding your product, please contact ANTLUX customer service via email. Our professional after-sales team is committed to providing timely assistance and ensuring your satisfaction.