ConStands Motorcycle Mover Stand User Manual

1. Introduction

This user manual provides essential information for the safe and effective use of your ConStands Motorcycle Mover Stand. This product is designed to facilitate easy maneuvering and precise positioning of your motorcycle in confined spaces, such as garages, sheds, or basements. It combines the functionality of a motorcycle stand with a maneuvering aid, allowing for minimal effort in parking and repositioning your bike.

Please read this manual thoroughly before initial use and keep it for future reference.

2. Safety Instructions

WARNING: Failure to follow these safety instructions may result in serious injury or damage to the motorcycle.

• Ensure the stand is placed on a flat, stable, and non-slip surface before use.
• Verify that the motorcycle is securely balanced and stable on the stand before releasing your grip.
• Do not exceed the maximum load capacity of 300 kg (661 lbs).
• Always operate the stand with caution and maintain control of the motorcycle.
• Keep hands and feet clear of moving parts and pinch points.
• Do not allow children or unauthorized persons to operate or play near the stand.
• Inspect the stand for any damage or wear before each use. Do not use if damaged.
• This stand is designed for parking and maneuvering. It is not intended for long-term storage without periodic checks or for use during maintenance requiring significant force.

3. Product Overview

The ConStands Mover II is a robust motorcycle stand designed for stability and ease of movement. It features a durable frame and four smooth-rolling wheels for effortless maneuvering. The width is adjustable to accommodate various motorcycle models.

Figure 3.1: Overview of the ConStands Motorcycle Mover Stand. This image shows the main frame of the stand, including the two upright supports and the four caster wheels, designed for easy movement.

Figure 3.2: Detail of the stand's base and wheels. This image highlights the sturdy construction of the base and the four durable caster wheels that enable smooth 360-degree movement.

4. Setup and Assembly

The ConStands Mover II stand typically comes pre-assembled or requires minimal assembly.

1. Unpacking: Carefully remove all components from the packaging. Check for any signs of damage during transit.
2. Component Check: Ensure all parts are present. The main components include the stand frame, two upright supports, and four wheels.
3. Wheel Installation (if required): If the wheels are not pre-installed, attach them securely to the designated points on the stand frame using the provided hardware. Ensure they are tightened properly.
4. Adjusting Width: The stand's width is adjustable from 23 cm to 36 cm. Loosen the adjustment bolts, slide the sections to the desired width to match your motorcycle's swingarm or frame, and then securely tighten the bolts.

5. Operating Instructions

Follow these steps to safely lift and maneuver your motorcycle using the ConStands Mover Stand.

1. Prepare the Motorcycle: Ensure the motorcycle is in neutral gear and the side stand is down.
2. Position the Stand: Place the ConStands Mover Stand directly behind the rear wheel of your motorcycle, ensuring the lifting points align with the motorcycle's swingarm bobbins or designated lifting points.


Figure 5.1: Proper positioning of the stand under the motorcycle's rear wheel. This image illustrates how the stand's lifting arms should align with the motorcycle's swingarm for stable support.

3. Lift the Motorcycle: While holding the motorcycle upright, firmly push down on the stand's lever arm (if applicable) or apply downward pressure on the stand until the motorcycle's rear wheel is lifted clear of the ground. Ensure both lifting points are securely engaged.


Figure 5.2: Motorcycle fully lifted and stable on the stand, side view. This image demonstrates the motorcycle securely resting on the stand, with its rear wheel elevated, ready for maneuvering.



Figure 5.3: Motorcycle fully lifted and stable on the stand, rear view. This image provides a clear view from the rear, showing the motorcycle perfectly balanced on the stand, highlighting its stability.

4. Maneuvering: Once the motorcycle is stable on the stand, you can easily push and pull it in any direction thanks to the four swivel wheels. Use smooth, controlled movements.
5. Lowering the Motorcycle: To lower the motorcycle, firmly hold the handlebars, apply slight downward pressure on the motorcycle to stabilize it, and then carefully release the stand's lever arm or lift the stand away from the motorcycle's lifting points. Ensure the side stand is deployed before fully releasing the motorcycle.

6. Maintenance

Proper maintenance will extend the life of your ConStands Mover Stand.

• Cleaning: Wipe down the stand with a damp cloth to remove dirt and grime. Avoid abrasive cleaners.
• Lubrication: Periodically apply a light lubricant to the wheel axles and any moving joints to ensure smooth operation.
• Inspection: Regularly inspect the stand for loose bolts, bent components, or signs of rust. Tighten any loose fasteners immediately.
• Storage: Store the stand in a dry place, away from direct sunlight and extreme temperatures, when not in use.

7. Troubleshooting

8. Specifications

• Product Name: ConStands Motorcycle Mover Stand
• Model: Mover II (sea-304152-101)
• Brand: ConStands
• Material: Steel
• Weight: Approximately 8.19 kg (18.05 lbs)
• Adjustable Width: 23 cm - 36 cm (9.05 inches - 14.17 inches)
• Maximum Load Capacity: 300 kg (661 lbs)
• Wheels: Four swivel caster wheels

9. Warranty and Support

ConStands products are manufactured to high-quality standards. For information regarding warranty coverage, please refer to the warranty card included with your purchase or visit the official ConStands website.

For technical support, spare parts, or any inquiries not covered in this manual, please contact ConStands customer service through their official channels.