1. Introduction
This manual provides instructions for the proper installation, operation, and maintenance of your Ibergrif Angled Water Isolating Valve, Model M22008A. This wall-mounted isolation tap is designed for reliable water flow control in various plumbing applications.
Key Features:
- Gleaming chrome coating for durability and aesthetic appeal.
- Constructed from brass with a grease chamber and double O-ring for enhanced waterproofing.
- Features a 1/2-inch wall connection and a 3/8-inch outlet connection.
- Ergonomic handle for easy operation.
- Protected against water return.
2. Product Overview
The Ibergrif Angled Water Isolating Valve is designed for efficient water control. It features a robust brass construction with a chrome finish, ensuring longevity and resistance to corrosion.
Figure 2.1: Main view of the Ibergrif Angled Water Isolating Valve with chrome finish.
Figure 2.2: Illustration emphasizing the heavy brass construction of the valve.
Figure 2.3: The valve showing its G3/8 inch outlet connection, suitable for connecting to faucets and toilets.
Figure 2.4: The valve featuring a blue indicator dot on the handle, typically indicating cold water.
Figure 2.5: A pair of valves, illustrating the rear connections and overall design.
Figure 2.6: Two valves displayed on a digital scale, indicating their approximate weight.
3. Dimensions
Refer to the diagram below for detailed dimensions of the Ibergrif Angled Water Isolating Valve.
Figure 3.1: Dimensional drawing of the valve, indicating key measurements such as overall length (79mm), outlet thread (G3/8"), inlet thread (G1/2"), and flange diameter (54mm).
4. Setup and Installation
Proper installation is crucial for the optimal performance and longevity of your valve. It is recommended that installation be performed by a qualified plumber.
4.1 Unboxing and Component Check
Before installation, carefully unbox the product and ensure all components are present and undamaged. The video below provides a visual guide to the product's components and initial assembly.
Video 4.1: A closer look at the Ibergrif Angled Water Isolating Valve, demonstrating unboxing and assembly of the handle and escutcheon plate.
4.2 Installation Steps
- Prepare the Installation Area: Ensure the main water supply is turned off before beginning installation. Clear the area around the wall connection point.
- Apply Thread Sealant: Apply appropriate thread sealant (e.g., PTFE tape) to the G1/2 inch inlet threads of the valve.
- Connect to Wall: Carefully screw the valve's G1/2 inch inlet into the wall water supply connection. Hand-tighten first, then use a wrench to secure it, ensuring not to overtighten.
- Install Escutcheon Plate: Slide the escutcheon plate (decorative flange) over the valve body until it sits flush against the wall, covering the connection point.
- Connect Outlet Hose: Apply thread sealant to the G3/8 inch outlet threads. Connect the flexible hose from your faucet or toilet to the valve's G3/8 inch outlet. Tighten securely.
- Check for Leaks: Slowly turn the main water supply back on. Inspect all connections for any signs of leaks. If leaks are detected, turn off the water supply and re-tighten the connections.
5. Operation
The Ibergrif Angled Water Isolating Valve features an ergonomic handle for easy control of water flow.
- To Open the Valve: Turn the handle counter-clockwise until the desired water flow is achieved.
- To Close the Valve: Turn the handle clockwise until the water flow stops completely. This isolates the connected fixture from the main water supply.
6. Maintenance
Regular maintenance helps preserve the appearance and functionality of your valve.
- Cleaning: Clean the chrome surface regularly with a soft cloth and mild soap or a non-abrasive cleaner specifically designed for chrome finishes. Avoid harsh chemicals, abrasive pads, or acidic cleaners, as these can damage the finish.
- Inspection: Periodically check for any signs of leaks around the connections. Address any leaks promptly to prevent water damage.
- Operation Check: Occasionally operate the valve (open and close) to ensure smooth functionality.
7. Troubleshooting
If you encounter issues with your Ibergrif Angled Water Isolating Valve, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Water Leakage at Connections | Loose connections, insufficient thread sealant, damaged O-rings. | Turn off water supply. Tighten connections. Reapply thread sealant if necessary. Inspect and replace O-rings if damaged. |
| Difficulty Turning Handle | Mineral buildup, internal component wear. | Ensure the valve is clean. If the issue persists, professional inspection may be required. |
| No Water Flow | Valve is closed, main water supply is off, blockage. | Ensure the valve is fully open. Check if the main water supply is on. Inspect for any blockages in the supply line. |
8. Specifications
| Feature | Detail |
|---|---|
| Brand | Ibergrif |
| Model Number | M22008A |
| Material | Brass |
| Exterior Finish | Chrome |
| Inlet Connection Size | 1/2 Inches (G1/2) |
| Inlet Connection Type | BSP |
| Outlet Connection Size | 3/8 Inches (G3/8) |
| Outlet Connection Type | Barb |
| Number of Ports | 2 |
| Valve Type | Needle Valve |
| Item Dimensions (L x W x H) | 3.24 x 1.61 x 1.06 inches (approx. 82 x 41 x 27 mm) |
| Specification Met | DVGW |
| Number of Pieces | 2 (per set) |
| UPC | 603922537502 |
9. Warranty
This Ibergrif Angled Water Isolating Valve comes with a five-year manufacturer's warranty. Please retain your proof of purchase for warranty claims. The warranty covers defects in materials and workmanship under normal use and service.
10. Support
For further assistance, technical support, or warranty inquiries, please contact Ibergrif customer service through their official website or the retailer where the product was purchased. Please have your model number (M22008A) and proof of purchase ready.