Kuvings EVO-800 Whole Slow Juicer Instruction Manual

1. Introduction

Thank you for purchasing the Kuvings EVO-800 Whole Slow Juicer. This appliance is designed to extract maximum nutrients from fruits and vegetables using a slow-press method. Its wide feeding chute minimizes preparation time, and the patented long screw efficiently processes various ingredients, including leafy greens. Please read this manual thoroughly before use to ensure safe and efficient operation and to understand all features of your new juicer.

2. Safety Precautions

• Always unplug the juicer from the power outlet before assembling, disassembling, or cleaning.
• Do not insert fingers or any utensils into the feeding chute or pulp outlet during operation. Use the provided pusher only.
• Ensure all parts are correctly and securely assembled before turning on the appliance.
• Keep the appliance out of reach of children and individuals with reduced physical, sensory, or mental capabilities.
• Do not operate the juicer continuously for more than 30 minutes. Allow it to cool down for at least 30 minutes before resuming operation to prevent motor overheating.
• Do not immerse the main body (motor base) in water or any other liquid.
• Do not process ingredients with hard seeds or pits (e.g., peach, avocado, mango) without removing them first, as this can damage the screw and other components.

3. Product Components

The Kuvings EVO-800 Whole Slow Juicer includes the following components:

• Main Body: The motor base of the juicer.
• Drum Lid: Covers the drum and contains the feeding chute.
• Drum: The main chamber where juicing occurs.
• Smart Cap: A spout cap to control juice flow and prevent drips.
• Rotating Wiper: Rotates to clean the strainer during juicing.
• Strainer: Filters the juice from the pulp.
• Screw (Auger): The main pressing component.
• Pusher: Used to guide ingredients into the feeding chute.
• Juice Cup: Collects the extracted juice.
• Pulp Container: Collects the separated pulp.
• Cleaning Brush: For general cleaning.
• Outlet Cleaning Brush: Specifically designed for cleaning the pulp outlet.
• Rotating Cleaning Brush: For efficient cleaning of the strainer.
• Recipe Book: Provides various juice recipes.
• Instruction Manual: This document.

Image: Assembled Kuvings EVO-800 with juice cup and pulp container in place.

Image: The frozen dessert strainer accessory, allowing for the creation of sorbets and frozen treats.

4. Setup

1. Unpack: Carefully remove all components from the packaging.
2. Wash Parts: Wash all detachable parts (drum lid, drum, smart cap, rotating wiper, strainer, screw, pusher, juice cup, pulp container) with warm, soapy water. Rinse thoroughly and dry. The main body should only be wiped with a damp cloth.
3. Assemble Drum: Place the drum onto the main body, ensuring it is securely seated.
4. Insert Wiper and Strainer: Place the rotating wiper into the drum, then insert the strainer into the rotating wiper.
5. Insert Screw: Place the screw into the center of the strainer, rotating it slightly until it drops into place.
6. Attach Drum Lid: Place the drum lid onto the drum, aligning the red dot on the lid with the red dot on the drum. Rotate the lid clockwise until it locks into place.
7. Position Containers: Place the juice cup under the juice spout and the pulp container under the pulp outlet.
8. Connect Power: Plug the power cord into a grounded electrical outlet.

5. Operating Instructions

1. Prepare Ingredients: Wash fruits and vegetables thoroughly. Due to the 8.2cm wide feeding chute, most ingredients do not require extensive pre-cutting. Remove any hard seeds, pits, or thick peels (e.g., pineapple skin, citrus peels).
2. Start Juicer: Ensure the smart cap is closed. Press the 'ON' button to start the motor.
3. Feed Ingredients: Slowly feed ingredients into the wide feeding chute. For longer or larger items, use the pusher to gently guide them down. Do not force ingredients.
4. Collect Juice and Pulp: The juice will flow into the juice cup, and the pulp will be expelled into the pulp container. Open the smart cap to release the juice.
5. Continuous Juicing: For continuous juicing, keep the smart cap open. For mixed juices, close the smart cap to allow ingredients to mix inside the drum before dispensing.
6. Finish Juicing: Once all ingredients are processed, allow the juicer to run for a few more seconds to extract any remaining juice. Press the 'OFF' button to stop the motor.

Image: The Kuvings EVO-800 in operation, processing fruits and vegetables.

Recipe Books

Your Kuvings EVO-800 comes with a recipe book to inspire various juice creations. Additionally, a 'Natural Fiber Foods Menu Book' is included, providing ideas for utilizing the leftover pulp, ensuring no waste.

Image: Included recipe books, offering various juice recipes and ideas for using pulp.

6. Maintenance and Cleaning

Regular cleaning is essential for maintaining the performance and longevity of your juicer. The EVO-800 is designed for easy disassembly and cleaning.

1. Disassemble: After use, turn off and unplug the juicer. Disassemble the drum lid, screw, strainer, rotating wiper, and drum in reverse order of assembly.
2. Rinse: Rinse all detachable parts under running water to remove large pulp residues.
3. Brush Cleaning: Use the provided cleaning brush to scrub the strainer and other parts. The rotating cleaning brush is particularly effective for the fine mesh of the strainer. Use the outlet cleaning brush for the pulp outlet.
4. Soak (Optional): For stubborn residue, soak parts in warm, soapy water for a few minutes before scrubbing.
5. Dry: Dry all parts thoroughly before reassembling or storing.
6. Main Body: Wipe the main body with a damp cloth. Do not submerge it in water.

7. Troubleshooting

8. Specifications

9. Warranty and Support

The Kuvings EVO-800 Whole Slow Juicer comes with a 10-year warranty, ensuring long-term reliability and peace of mind. This warranty covers manufacturing defects and significant operational issues under normal use.

For technical support, warranty claims, or inquiries regarding your product, please contact Kuvings customer service through their official website or the retailer where the product was purchased. Please have your model number (EVO-800) and proof of purchase ready when contacting support.