1. Introduction
This manual provides detailed instructions for the Dioche RFID Reader Module, model Dioche41cwakzi35. This embedded access control module operates at 125kHz and is designed for integration into various systems requiring RFID card reading capabilities. It features a compact design and offers a card reading distance of 5 to 15 cm.
2. Product Features
- Embedded access module RFID module.
- Effective card reading distance: 5 to 15 cm.
- Compatible with all 125kHz cards, including EN4100 cards.
- Includes wiring diagram for installation.
- Operating voltage: DC 9-12V.
- Operating current: 60mA-80mA.
- Working temperature range: -40°C to 60°C.
- User capacity: 2000.
3. Specifications
| Specification | Value |
|---|---|
| Brand | Dioche |
| Model Number | Dioche41cwakzi35 |
| Working Voltage | DC 9-12V |
| Working Current | 60mA-80mA |
| Card Reading Distance | 5-15 cm |
| Working Temperature | -40°C - 60°C |
| User Capacity | 2000 |
| Supported Card Type | EN4100 Card or All ID Cards (125khz) |
| Manufacturer | Dioche |
| UPC | 739879364257 |
4. What's in the Box
- 1 x RFID Module
- 1 x Harness
- 1 x Manual (this document)
5. Product Overview
6. Setup and Wiring
Proper setup and wiring are essential for the correct operation of the RFID Reader Module. Refer to the wiring diagram below for connection details.
6.1. Power Connection
Connect the module to a DC 9-12V power source using the provided harness. Ensure correct polarity to prevent damage to the module.
6.2. Antenna Connection
Connect the RFID antenna coil to the designated antenna interface (J3-AJ3-B) on the module. The antenna is crucial for reading RFID cards.
6.3. Output Connections
Depending on your application, connect the module's output terminals (e.g., relay output, data lines) to your control system. Refer to the specific pinout on the module or the wiring diagram for detailed information on each connection point.
7. Operating Instructions
Once the module is correctly powered and wired, it is ready to read 125kHz RFID cards.
7.1. Card Reading
Present a compatible 125kHz RFID card or tag within the effective reading distance of 5-15 cm from the antenna. The module will detect the card and process its data. An indicating LED on the board typically illuminates, and a buzzer may sound to confirm a successful read.
8. Maintenance
The Dioche RFID Reader Module is designed for durability and requires minimal maintenance.
- Cleaning: Keep the module and antenna free from dust and debris. Use a soft, dry cloth for cleaning. Avoid using liquid cleaners directly on the electronic components.
- Environmental Conditions: Operate the module within the specified working temperature range of -40°C to 60°C. Avoid exposure to extreme humidity or corrosive environments.
- Physical Inspection: Periodically check for any visible damage to the board, wiring, or antenna. Ensure all connections remain secure.
9. Troubleshooting
If you encounter issues with your RFID Reader Module, consider the following troubleshooting steps:
- No Power/Module Not Responding:
- Verify the power supply is providing DC 9-12V.
- Check all power connections for proper seating and polarity.
- Ensure the power source is capable of supplying the required 60mA-80mA current.
- Card Not Reading:
- Confirm that the card being used is a 125kHz RFID card (e.g., EN4100 compatible).
- Ensure the card is presented within the 5-15 cm reading range of the antenna.
- Check the antenna connection to the module; ensure it is securely attached.
- Avoid placing the antenna near large metal objects that could interfere with the RFID signal.
- Incorrect Data Output/Communication Issues:
- Review the wiring diagram (Figure 6.1) to ensure all data output lines are correctly connected to your control system.
- Consult the documentation for your specific control system to ensure it is configured to receive data from the RFID module correctly.
- If using a serial interface, verify baud rates and communication protocols match between the module and your system.
If issues persist after following these steps, contact customer support for further assistance.
10. Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact Dioche customer service through the retailer where the product was purchased. Provide your model number (Dioche41cwakzi35) and any relevant purchase details when seeking support.