Interstate Batteries 920005

Download PDF
Contents

Interstate Batteries 1.0 Amp Powersports Battery Charger and Maintainer (Model 920005)

User Instruction Manual

1. Introduction

This manual provides essential instructions for the safe and effective use of your Interstate Batteries 1.0 Amp Powersports Battery Charger and Maintainer, Model 920005. This device is designed to charge and maintain 12-volt Sealed Lead Acid (SLA) and Absorbent Glass Mat (AGM) batteries commonly found in powersports vehicles and equipment.

2. Safety Information

WARNING: Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

  • Always read and understand all instructions before using the charger.
  • Ensure proper ventilation when charging batteries.
  • This charger is designed with safety features including short-circuit protection, reverse polarity protection, and a spark-proof design to prevent accidental sparks during connection.
  • Do not attempt to charge non-rechargeable batteries.
  • Keep out of reach of children.
  • Avoid exposing the charger to rain or excessive moisture.

3. Product Overview

The Interstate Batteries 1.0 Amp Powersports Battery Charger (Model 920005) is an automatic, microprocessor-controlled charger and maintainer. It features a durable plastic case and LED indicators for easy monitoring of the charging status.

Components Included:

  • Guardian 1 Charger Unit
  • Battery Cables with Alligator Clamps
  • Battery Cables with Ring Terminals
  • Wall Plug (AC Power Cord)
  • Owner's Manual (this document)

LED Indicators:

  • A.C. Power: Indicates the charger is connected to an active power outlet.
  • Charging: Illuminates when the battery is actively being charged.
  • Float: Illuminates when the battery is fully charged and the charger has switched to maintenance mode.
Interstate Batteries 1.0 Amp Powersports Battery Charger with alligator clips and ring terminals

Image: The Interstate Batteries 1.0 Amp Powersports Battery Charger unit, shown with its detachable alligator clamps and ring terminal connectors.

4. Setup

Follow these steps to properly set up your battery charger:

  1. Prepare the Battery: Ensure the battery terminals are clean and free of corrosion. If necessary, clean them with a wire brush and a battery terminal cleaner.
  2. Select Connectors: Choose between the alligator clamps or ring terminals based on your battery's terminal type and accessibility. The charger comes with both options.
  3. Connect to Battery:
    • Connect the RED (+) positive connector to the positive battery terminal.
    • Connect the BLACK (-) negative connector to the negative battery terminal.
    • Ensure connections are secure. The charger's microprocessor will detect the battery type (regular, enhanced, or AGM).
  4. Connect to Power: Plug the charger's AC power cord into a standard 120V AC wall outlet. The 'A.C. Power' LED indicator on the charger should illuminate.
Interstate Batteries 1.0 Amp Powersports Battery Charger connected to a battery in a vehicle

Image: The battery charger connected to a powersports battery within a vehicle, demonstrating proper setup.

5. Operating Instructions

Once properly connected, the charger will automatically begin its charging cycle.

  1. Initial Connection: After connecting to the battery and AC power, the 'A.C. Power' LED will light up.
  2. Charging Phase: The 'Charging' LED will illuminate, indicating that the charger is actively supplying current to the battery. The smart charger's microprocessor will automatically adjust the charging rate based on the battery's condition and type (Sealed Lead Acid, AGM, Conventional, or Gel Cell).
  3. Float/Maintenance Mode: Once the battery reaches a full charge (approximately 14.4 volts DC), the 'Charging' LED will turn off, and the 'Float' LED will illuminate. This signifies that the charger has transitioned into maintenance mode, providing a trickle charge to keep the battery at optimal capacity without overcharging.
  4. Disconnecting: To disconnect the charger, first unplug the AC power cord from the wall outlet. Then, disconnect the negative (-) connector from the battery, followed by the positive (+) connector.

The charger is designed for continuous connection in maintenance mode, making it ideal for vehicles in long-term storage.

6. Maintenance

The Interstate Batteries 1.0 Amp Powersports Battery Charger also functions as a battery maintainer. This feature is crucial for extending battery life, especially for vehicles or equipment stored for extended periods.

  • Long-Term Storage: For motorcycles, ATVs, marine vehicles, snowmobiles, lawnmowers, or scooters that are not used regularly, connect the charger and leave it in 'Float' mode. This prevents self-discharge and ensures the battery remains fully charged and ready for use.
  • Cleaning: Periodically wipe the charger unit with a dry cloth to remove dust and debris. Do not use liquid cleaners or immerse the unit in water.
  • Cable Inspection: Regularly inspect the battery cables and connectors for any signs of damage, fraying, or corrosion. Replace if necessary.

7. Troubleshooting

If you encounter issues with your charger, refer to the following common problems and solutions:

ProblemPossible CauseSolution
No LEDs illuminate when plugged in.No AC power; faulty outlet; charger malfunction.Check wall outlet with another device. Ensure charger is securely plugged in. If problem persists, contact support.
'Charging' LED does not illuminate after connecting to battery.Incorrect battery connection (reverse polarity); battery is already fully charged; severely discharged battery.Verify positive and negative connections. If battery is full, 'Float' LED should be on. For severely discharged batteries, it may take time to register. If no change, battery may be faulty.
'Float' LED does not illuminate after extended charging.Battery not reaching full charge; charger malfunction.Ensure battery is capable of holding a charge. Charging time varies by battery size and discharge level. If charging for over 24 hours and 'Float' is not active, the battery may be faulty or the charger may require service.
Charger feels warm during operation.Normal operation.It is normal for the charger to feel warm during the charging process. Ensure adequate ventilation around the unit.

8. Specifications

FeatureDetail
Model Number920005
Input Voltage120V AC, 60Hz
Output Voltage14.4 Volts (DC)
Charging Current1.0 Amp (1000mA)
Battery Types Supported12V Sealed Lead Acid (SLA), AGM, Conventional, Gel Cell
Product Dimensions5.2 x 2.91 x 1.89 inches
Item Weight1.12 pounds
ManufacturerInterstate Batteries

9. Warranty & Support

This Interstate Batteries charger comes with a 12-month hassle-free warranty from the date of purchase. Please retain your proof of purchase for warranty claims.

For technical support, warranty inquiries, or further assistance, please contact Interstate Batteries customer service:

When contacting support, please have your product model number (920005) and purchase details available.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.