612 Vermont VT-1620A-4

Download PDF
Contents

612 Vermont Battery Operated LED Window Candle Instruction Manual

Model: VT-1620A-4

Brand: 612 Vermont

Introduction

This manual provides detailed instructions for the setup, operation, and maintenance of your 612 Vermont Battery Operated LED Window Candles, Model VT-1620A-4. These candles feature a patented dual LED flicker flame, a light sensor for automatic dusk-on activation, and an 8-hour timer. Please read this manual thoroughly before use to ensure proper functionality and longevity of your product.

Included Components:

  • LED Window Candle units (Pack of 4)
  • Candle bases
  • Instruction Manual

Note: 3 AA batteries are required per candle and are not included.

Setup

1. Battery Installation

  1. Locate the battery compartment at the bottom of the candle base.
  2. Open the battery compartment cover.
  3. Insert 3 AA batteries into the compartment, ensuring correct polarity (+/-).
  4. Close the battery compartment cover securely.
Image showing the battery compartment at the base of the LED window candle.

Figure 1: Battery compartment located at the base of the candle for stability.

2. Placement and Sensor Orientation

Place the candle on your windowsill or desired surface. Ensure the small light sensor hole, located on the side of the candle, is facing outwards towards the window. This allows the sensor to detect ambient light levels for automatic operation.

Image of an LED window candle placed on a windowsill, illuminated at night.

Figure 2: Proper placement of the LED window candle on a windowsill.

3. Initial Power On

Locate the slide switch on the side of the candle. Move the switch to the middle position for flickering flame or the top position for a steady light. The candle will then be ready for operation based on the light sensor.

Video 1: Demonstration of battery installation, slide switch operation, and sensor functionality for the 612 Vermont LED Window Candle.

Operating Instructions

1. Light Sensor and Timer Functionality

The 612 Vermont LED Window Candle is equipped with a light-dependent resistor (LDR) sensor. When the slide switch is in either the flicker or steady-on position, the candle will automatically turn on at dusk (when ambient light levels decrease) and remain lit for approximately 8 hours. After 8 hours, the candle will automatically turn off. It will then reactivate the following dusk.

2. Selecting Light Mode

  • Flicker Mode: Slide the switch to the middle position for a realistic flickering flame effect.
  • Steady-On Mode: Slide the switch to the top position for a constant, steady light.
  • Off: Slide the switch to the bottom position to turn the candle off completely.
Image highlighting the features of the LED window candle, including flicker flame, slide switch, and soft tip flame.

Figure 3: Features of the 612 Vermont LED Window Candle, including the slide switch for light mode selection.

Maintenance

1. Battery Replacement

When the light output diminishes or the candle stops illuminating, it is time to replace the batteries. Follow the battery installation steps in the "Setup" section. It is recommended to replace all 3 AA batteries simultaneously for optimal performance.

2. Cleaning

To clean the candle, gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water. Ensure the light sensor is kept clear of dust and debris for accurate operation.

Troubleshooting

ProblemPossible CauseSolution
Candle does not turn on at dusk.
  • 1. Batteries are dead or incorrectly installed.
  • 2. Light sensor is obstructed or facing indoors.
  • 3. Ambient light is too bright.
  • 4. Slide switch is in the "Off" position.
  • 1. Replace batteries and check polarity.
  • 2. Ensure sensor faces outdoors and is clear.
  • 3. Move candle to a darker location or wait for darker conditions.
  • 4. Move slide switch to flicker or steady-on position.
Candle turns off too early or too late.
  • 1. Inconsistent light sensor readings.
  • 2. Batteries are low.
  • 1. Ensure sensor is not partially obstructed or exposed to fluctuating light.
  • 2. Replace batteries.
Flicker effect is not working.
  • 1. Slide switch is in the steady-on position.
  • 1. Move slide switch to the middle position for flicker mode.

Specifications

FeatureDetail
Model NumberVT-1620A-4
Power Source3 AA Batteries (not included)
Battery LifeApproximately 70 days (1680 hours) on one set of batteries
Light SourceDual LED (Warm White)
Light ModesFlicker Flame, Steady-On
Sensor TechnologyLight Dependent Resistor (LDR) for dusk-on activation
Timer8-hour automatic timer
Dimensions (Overall)12" H x 3.125" W x 1.75" D
Candlestick Diameter7/8"
Base MaterialBronze (Antique Bronze finish)
MaterialPlastic
Indoor/Outdoor UsageIndoor
Diagram showing the dimensions of the LED window candle, including height, width, depth, flame height, candlestick height, and base height.

Figure 4: Detailed dimensions of the 612 Vermont LED Window Candle.

Warranty Information

Warranty information for the 612 Vermont Battery Operated LED Window Candle (Model VT-1620A-4) is not explicitly detailed in the provided product information. Please refer to the product packaging or contact 612 Vermont customer support for specific warranty terms and conditions.

Support Information

For further assistance, technical support, or inquiries regarding your 612 Vermont LED Window Candles, please contact the manufacturer or refer to their official website. Contact details are typically provided on the product packaging or within the purchase documentation.

© 2026 612 Vermont. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.