Product Overview
This manual provides essential information for the installation, operation, and maintenance of your BRITA On Tap HF Water Filter Cartridge. This cartridge is designed for use with the BRITA On Tap filtration system to provide filtered water directly from your tap.
Image: The BRITA On Tap HF Water Filter Cartridge shown in its retail packaging, indicating a single cartridge.
Key Features:
- Preserves valuable water minerals such as calcium and magnesium while reducing chlorine and other substances that alter taste, providing excellent tasting water for drinking and preparing hot drinks.
- Features an activated carbon filter to reduce taste-altering substances, an ionic exchanger to reduce metals like lead, and a hollow fiber membrane to filter particles and 99.9% of bacteria.
- Designed for approximately 600 liters of filtered water per cartridge.
- Compatible exclusively with the new BRITA On Tap System.
Image: The BRITA On Tap filtration system attached to a faucet, with the filter cartridge shown separately, highlighting its 600-liter capacity.
Image: A hand holding the BRITA On Tap filter cartridge, illustrating its compact size with dimensions of approximately 3.7 inches (9 cm) in height.
Setup and Installation
The BRITA On Tap HF Water Filter Cartridge is designed for easy, tool-free installation into your existing BRITA On Tap filtration system. Follow these steps to replace or install a new cartridge:
Image: Installation steps 1 and 2. Step 1 shows removing the protective cap from the new cartridge. Step 2 shows inserting the cartridge into the BRITA On Tap system.
Image: Installation steps 3 and 4. Step 3 shows pushing the cartridge fully into the system. Step 4 shows securing the outer ring or cap.
- Step 1: Remove the old cartridge (if applicable) and prepare the new one. Gently twist and pull the old cartridge out. Unpack the new BRITA On Tap HF Water Filter Cartridge and remove any protective caps.
- Step 2: Insert the new cartridge. Align the new cartridge with the opening in the BRITA On Tap system. Push it firmly into place until it is securely seated.
- Step 3: Secure the cartridge. Ensure the cartridge is fully inserted and any outer rings or caps are securely fastened.
- Step 4: Flush the system. After installation, allow water to run through the system for a few minutes to flush out any air and initial carbon dust. Refer to your BRITA On Tap system's main manual for specific flushing instructions and to reset the filter life indicator.
Operating the System with the Cartridge
Once the BRITA On Tap HF Water Filter Cartridge is installed, your BRITA On Tap system is ready to provide filtered water. The system typically features a display that shows the filter status and indicates when a cartridge change is needed. The system also allows for easy water flow change with three positions: unfiltered stream, unfiltered spray, and filtered stream.
Image: The BRITA On Tap system in operation, demonstrating its use for both washing produce with unfiltered water and dispensing filtered water into a glass for drinking.
Image: A couple in a kitchen, with one person filling a glass with filtered water from the BRITA On Tap system, illustrating everyday use.
Filter Technology:
The BRITA On Tap HF Water Filter Cartridge employs a multi-stage filtration process:
- Hollow Fiber Membrane: Filters microparticles and 99.9% of bacteria.
- Activated Carbon Filter: Reduces substances that alter the taste of water, such as chlorine, pesticides, and herbicides.
- Ion Exchange Resin: Reduces metals like lead.
- Mineral Preservation: Designed to preserve valuable water minerals such as calcium and magnesium.
Image: A detailed diagram showcasing the internal components and multi-stage filtration process of the BRITA On Tap system, including the hollow fiber membrane, activated carbon, and ion exchange resin, and their respective functions in purifying water.
Image: An illustration of the BRITA On Tap system highlighting its ability to reduce microplastics from tap water.
Maintenance
The primary maintenance for the BRITA On Tap HF Water Filter Cartridge involves timely replacement. Each cartridge is designed to filter approximately 600 liters of water.
- Cartridge Life: The cartridge typically lasts for about 600 liters of filtered water. The exact lifespan may vary depending on local water quality and usage.
- Replacement Indicator: Your BRITA On Tap system features a display that indicates the filter status and will notify you when the cartridge needs to be changed. Follow the system's instructions to reset the indicator after installing a new cartridge.
- Disposal: Dispose of used cartridges according to local recycling guidelines.
Troubleshooting
This section addresses common issues you might encounter with your BRITA On Tap HF Water Filter Cartridge. For issues related to the BRITA On Tap system itself, please refer to the system's dedicated instruction manual.
| Problem | Possible Cause | Solution |
|---|---|---|
| Reduced water flow from filtered stream. | Cartridge is nearing end of life or is clogged. | Replace the filter cartridge. Ensure the new cartridge is properly seated. |
| Unpleasant taste or odor in filtered water. | Cartridge has exceeded its capacity or is expired. | Replace the filter cartridge immediately. Ensure initial flushing of new cartridge. |
| Filter status display not resetting after cartridge change. | Incorrect reset procedure or system malfunction. | Refer to your BRITA On Tap system's manual for specific instructions on resetting the display. Ensure the cartridge is fully inserted. |
Specifications
| Feature | Detail |
|---|---|
| Brand | BRITA |
| Model Name | BRITA ON Tap (Cartridge for On Tap System) |
| Item Model Number | 1037406 |
| ASIN | B07YG63BQJ |
| Special Feature | Chlorine Reduction, Lead Reduction, Pesticide Reduction, Herbicide Reduction, Bacteria Filtration (99.9%) |
| Product Dimensions | 3.78"L x 2.44"W x 2.44"H (approx. 9.6cm x 6.2cm x 6.2cm) |
| Item Weight | 120 Grams (4.2 ounces) |
| Package Information | Cartridge |
| Installation Type | Designed for BRITA On Tap faucet systems |
| Supported Water TDS Level Maximum | 500 PPM |
| Estimated Cartridge Life | 600 Liters |
| Date First Available | October 11, 2019 |
Image: A visual guide indicating the compatibility of the filter cartridge with the modern BRITA On Tap system (marked with a green check) and its incompatibility with older BRITA faucet filters (marked with a red cross).
Warranty Information
Specific warranty details for the BRITA On Tap HF Water Filter Cartridge are not provided in the product information. For warranty inquiries regarding your BRITA On Tap system or its components, please refer to the documentation included with your original BRITA On Tap system or contact BRITA customer support directly.
Customer Support
For further assistance, questions, or support regarding your BRITA On Tap HF Water Filter Cartridge or the BRITA On Tap system, please visit the official BRITA website or contact their customer service department. Contact information can typically be found on the BRITA packaging or their official website.
Note: Always ensure you are using genuine BRITA replacement cartridges to maintain optimal performance and filtration quality.
