Jada Toys Big Time Muscle Drift 1:10 Scale RC, 2019 Ford Mustang - Wide Body, Black

Introduction

Welcome to the instruction manual for your Jada Toys Big Time Muscle Drift 1:10 Scale RC 2019 Ford Mustang Wide Body. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your new remote-controlled vehicle. Please read this manual thoroughly before first use to ensure safe and optimal performance of your RC car.

Safety Information

WARNING: CHOKING HAZARD - Small Parts. Not for children under 3 years.

• Always operate the RC vehicle in a safe, open area away from people, pets, and obstacles.
• Do not operate near water or in wet conditions to prevent electrical damage.
• Keep fingers, hair, and loose clothing away from moving parts, especially the wheels.
• Adult supervision is recommended for children operating this product.
• Do not attempt to modify or disassemble the RC vehicle or controller. This may cause damage and void the warranty.
• Use only the specified batteries and charging methods.
• Remove batteries from the controller and vehicle when not in use for extended periods.

What's Included

Your package should contain the following items:

• 1 x Jada Toys Big Time Muscle Drift 1:10 Scale RC 2019 Ford Mustang Wide Body (Black)
• 1 x Pistol Grip Controller (2.4 GHz)
• 1 x Set of Extra Drift Tires
• 1 x USB Charging Cable
• AA Batteries (for controller)

Image showing the Jada Toys Big Time Muscle Drift RC car, its pistol grip controller, and the included extra set of drift tires.

Setup

1. Charging the Vehicle Battery

The RC car is powered by a built-in rechargeable battery. Before first use, ensure the vehicle's battery is fully charged.

1. Locate the USB charging port on the underside or side of the RC car.
2. Connect the small end of the included USB charging cable to the vehicle's charging port.
3. Connect the larger USB end of the cable to a standard USB power adapter (not included) or a computer USB port.
4. The charging indicator light on the cable or vehicle will illuminate during charging and turn off or change color when fully charged. Charging typically takes approximately 30 minutes for a full charge, providing around 15 minutes of continuous driving time.
5. Once fully charged, disconnect the USB cable from both the vehicle and the power source.

2. Installing Controller Batteries

The pistol grip controller requires AA batteries, which are included.

1. Locate the battery compartment on the back or bottom of the pistol grip controller.
2. Open the battery compartment cover.
3. Insert the AA batteries, ensuring correct polarity (+ and -) as indicated inside the compartment.
4. Close the battery compartment cover securely.

Operating Instructions

1. Powering On and Pairing

1. Ensure both the RC car and the controller are fully charged/have fresh batteries.
2. Turn on the power switch on the RC car (usually located on the underside or top).
3. Turn on the power switch on the pistol grip controller.
4. The controller and car should automatically pair. An indicator light on the controller or car may stop blinking and become solid once paired.
5. The 2.4 GHz frequency allows multiple players (up to 16+) to operate their RC vehicles simultaneously within a range of 100 feet without interference.

2. Controller Functions

• Steering Wheel: Rotate the wheel left or right to steer the RC car.
• Trigger: Pull the trigger towards you to move the car forward. Push the trigger away from you to reverse the car.
• Turbo Button: Press this button to activate the high-performance drifting feature. This will allow the rear tires to lose traction and initiate controlled drifts.

3. Driving and Drifting

• Basic Driving: Use the steering wheel and trigger to navigate the car. Practice smooth acceleration and steering.
• Initiating Drifts: While moving forward, press the Turbo Button and simultaneously turn the steering wheel sharply in the desired drift direction. Experiment with throttle control to maintain the drift.
• For optimal drifting performance, use the included extra set of drift tires.

Front view of the RC car, highlighting its wide body design and detailed grille.

Side profile of the RC car, showcasing its sleek design and gold-colored wheels.

Maintenance

1. Cleaning

• After each use, gently wipe the RC car with a soft, dry cloth to remove dust and debris.
• Do not use water or chemical cleaners, as this can damage the electronics.
• Ensure no foreign objects are lodged in the wheels or chassis.

2. Tire Replacement

The product comes with an extra set of tires, ideal for enhanced drifting performance.

1. To remove a tire, gently pull it off the wheel hub.
2. Align the new tire with the wheel hub and push it firmly into place until it is securely seated.
3. Ensure all tires are properly attached before operating the vehicle.

Troubleshooting

Specifications

Warranty and Support

For information regarding warranty coverage, product support, or replacement parts, please contact Jada Toys customer service directly or refer to the product packaging for specific details. You may also visit the official Jada Toys website for further assistance.

Jada Toys Official Website: www.jadatoys.com