Product Overview
The Trevi SLD 3P50 is a digital clock thermometer featuring a large, backlit LCD display. It includes a programmable alarm and a snooze function, designed for clear readability and ease of use in various indoor environments.
Image: Front view of the Trevi SLD 3P50 Digital Clock Thermometer, displaying the current time, date, day of the week, and indoor temperature.
Package Contents
- 1 x Trevi SLD 3P50 Digital Clock Thermometer
- 1 x User Manual (this document)
- Note: Batteries are not included and must be purchased separately.
Setup
1. Battery Installation
- Locate the battery compartment on the back of the device.
- Open the battery compartment cover.
- Insert the required batteries (typically AAA, refer to the compartment label for exact type and polarity). Ensure correct polarity (+/-).
- Close the battery compartment cover securely.
2. Initial Power On
Upon battery installation, the device will power on automatically. The display will show default time and date settings, and the current temperature.
3. Setting Time and Date
- Press the MODE button to cycle through display modes until the time setting mode is active (usually indicated by flashing digits).
- Use the UP and DOWN buttons to adjust the hour, then press MODE to confirm and move to minutes.
- Repeat this process for setting the year, month, and day.
- Press MODE again to exit the setting mode.
Operating Instructions
1. Display Modes
Press the MODE button to switch between different display modes, such as Time, Date, and Alarm settings.
2. Setting the Alarm
- Press MODE until the alarm time is displayed (often indicated by an alarm icon).
- Press and hold MODE until the alarm hour digits flash.
- Use the UP and DOWN buttons to set the desired alarm hour.
- Press MODE to confirm and move to minutes, then set minutes.
- Press MODE again to save the alarm setting.
- To activate/deactivate the alarm, press the ALARM ON/OFF button (or similar, refer to device buttons). An alarm icon will appear/disappear on the display.
3. Using the Snooze Function
When the alarm sounds, press the SNOOZE/LIGHT button (usually located on top) to temporarily silence the alarm. The alarm will sound again after a few minutes (typically 5-10 minutes).
4. Backlight Activation
Press the SNOOZE/LIGHT button to activate the display backlight for a few seconds, improving visibility in low-light conditions.
5. Temperature Display
The device continuously displays the ambient temperature. Some models may allow switching between Celsius and Fahrenheit. If available, press a dedicated °C/°F button or refer to the manual for specific button combinations.
Maintenance
1. Cleaning
- Wipe the device with a soft, dry cloth.
- Do not use abrasive cleaners, solvents, or chemical sprays, as these may damage the surface or internal components.
2. Battery Replacement
When the display dims or functions become erratic, it is time to replace the batteries. Follow the battery installation steps in the Setup section. Always replace all batteries at the same time with new ones of the same type.
3. Storage
If the device will not be used for an extended period, remove the batteries to prevent leakage and potential damage.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Display is blank or dim. | Low or dead batteries; incorrect battery installation. | Replace batteries with new ones, ensuring correct polarity. |
| Alarm does not sound. | Alarm is not activated; alarm volume is too low (if adjustable). | Ensure the alarm function is turned ON. Check if there's a volume setting. |
| Incorrect time/date. | Time/date was not set correctly or reset after battery change. | Follow the "Setting Time and Date" instructions in the Setup section. |
| Temperature reading seems inaccurate. | Device placed near heat sources, direct sunlight, or drafts. | Relocate the device to a stable indoor environment away from extreme temperature fluctuations. |
Specifications
Image: Trevi SLD 3P50 Digital Clock Thermometer, illustrating its approximate height (11.18 cm) and width (13.46 cm).
| Feature | Detail |
|---|---|
| Model Number | 0SL3P50 |
| Dimensions (L x W x H) | 50 x 50 x 28 cm |
| Weight | 160 grams |
| Brand | Trevi |
| Color | Red |
| Display Type | Digital, Backlit LCD |
| Special Features | Temperature display, Large screen, Alarm, Snooze |
| Power Source | Battery powered |
| Batteries Included | No |
| Mounting Type | Table mount |
| Material | Stainless steel |
| Operating Mode | Electric |
| Watch Movement Type | Quartz |
Warranty and Support
This product is covered by a standard manufacturer's warranty. For detailed warranty information, please refer to the warranty card included with your purchase or contact Trevi customer support.
For technical assistance, troubleshooting not covered in this manual, or service inquiries, please visit the official Trevi website or contact their customer service department. Contact details can typically be found on the product packaging or the manufacturer's website.
- Manufacturer: Trevi
- Model: SLD 3P50 (0SL3P50)
- ASIN: B07Y3T2BFV