Einhell TE-AG 18/115 Li 18V Cordless Angle Grinder Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective operation of your Einhell TE-AG 18/115 Li 18V Cordless Angle Grinder. Please read all instructions carefully before use and retain this manual for future reference.

The Einhell TE-AG 18/115 Li is a lightweight and compact cordless angle grinder designed for abrasive cutting and polishing tasks. It features a robust aluminum gearbox, soft-start safeguard, and an ergonomic design for comfortable and precise control. This tool is part of the Einhell Power X-Change family, allowing for battery interchangeability with other compatible tools.

Key Features:

• Power X-Change System: Utilizes the versatile 18-Volt battery system compatible with all Einhell Power X-Change tools.
• Powerful Performance: Delivers smooth and consistent operation with up to 8,500 RPM.
• Enhanced Safety: Equipped with soft start and restart protection for user safety, along with overload protection for device longevity.
• Durable Construction: Features aluminum gearing and optimized ventilation for increased service life and improved cooling.
• Ergonomic Handling: Includes a 3-position easy-connect auxiliary handle for customizable comfort and control.

2. Safety Information

Always observe general safety regulations when using power tools. Failure to follow these instructions may result in electric shock, fire, and/or serious injury.

General Power Tool Safety Warnings:

• Work Area Safety: Keep the work area clean and well-lit. Cluttered or dark areas invite accidents. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
• Electrical Safety: Avoid body contact with earthed or grounded surfaces. Do not expose power tools to rain or wet conditions.
• Personal Safety: Always wear eye protection. Use hearing protection when operating for extended periods. Wear a dust mask if operations create dust. Dress properly; avoid loose clothing or jewelry.
• Tool Use and Care: Do not force the power tool. Use the correct power tool for your application. Disconnect the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
• Battery Tool Use and Care: Recharge only with the charger specified by the manufacturer. Use power tools only with specifically designated battery packs.

Specific Safety Warnings for Grinding Operations:

• This power tool is intended to function as a grinder. Read all safety warnings, instructions, illustrations, and specifications provided with this power tool.
• Always use the correct type of grinding disc for the material and application.
• Ensure the disc is securely mounted and free from damage before each use.
• Never operate the tool without the guard properly installed and adjusted.
• Maintain a firm grip on the tool and position your body to resist kickback forces.

3. Components and Parts

Familiarize yourself with the various parts of your Einhell TE-AG 18/115 Li angle grinder for safe and efficient operation.

Figure 1: Einhell TE-AG 18/115 Li Cordless Angle Grinder. This image shows the main body of the angle grinder, highlighting its compact design and the outline of a compatible Power X-Change battery, which is sold separately.

Figure 2: Side view of the angle grinder. This image provides a closer look at the auxiliary handle and the disc guard, which are crucial for control and safety during operation.

• Main Handle: Ergonomic grip for primary control.
• Auxiliary Handle: Provides additional grip and control, attachable in multiple positions.
• Spindle Lock Button: Used to lock the spindle for disc changes.
• On/Off Switch: Activates and deactivates the tool.
• Disc Guard: Adjustable guard for protection against sparks and debris.
• Grinding Disc/Cutting Disc (not included): The abrasive accessory for material removal.
• Battery Pack (not included): Provides power to the tool.

4. Setup

Before operating the angle grinder, ensure proper assembly and battery installation.

4.1 Attaching the Auxiliary Handle

The auxiliary handle can be attached in three different positions (left, right, or top) to suit your working preference and application.

Figure 3: Angle grinder demonstrating the three possible positions for attaching the auxiliary handle, allowing for versatile and comfortable use.

1. Screw the auxiliary handle firmly into the desired threaded opening on the gear head.

4.2 Mounting the Disc Guard

The disc guard must always be used for safety and adjusted to direct sparks away from you.

1. Place the disc guard onto the collar of the gear housing.
2. Rotate the guard to the desired position, ensuring it covers the top of the disc and directs sparks away from the operator.
3. Tighten the clamping lever to secure the guard in place.

4.3 Installing/Changing Grinding Discs

Always ensure the tool is switched off and the battery is removed before changing discs.

1. Press and hold the spindle lock button.
2. Use the supplied spanner wrench to loosen and remove the clamping nut.
3. Remove the old disc and clean the flanges.
4. Place the new disc onto the lower flange, ensuring it sits flat.
5. Screw on the clamping nut and tighten it firmly with the spanner wrench while holding the spindle lock button.

4.4 Battery Installation

This tool is sold without a battery or charger. Use only Einhell Power X-Change 18V batteries.

1. Ensure the battery is fully charged.
2. Slide the charged battery pack into the battery receptacle on the tool until it clicks into place.
3. To remove, press the battery release button and slide the battery out.

5. Operating Instructions

Follow these steps for safe and effective operation of your angle grinder.

5.1 Switching On and Off

1. To Switch On: Push the On/Off switch forward and then press it down.
2. To Switch Off: Release the On/Off switch. If the switch is locked in the ON position, press the rear part of the switch to release it.

5.2 Grinding and Cutting Techniques

Always allow the disc to reach full speed before contacting the workpiece.

Figure 4: The angle grinder in operation, illustrating the direction of cutting and the protective function of the disc guard.

• Grinding: Hold the tool at an angle of approximately 15-30 degrees to the workpiece. Apply moderate pressure and move the tool evenly across the surface.
• Cutting: Hold the tool at a 90-degree angle to the workpiece. Apply light, even pressure. Do not tilt the cutting disc, as this can cause it to jam or break.
• Ensure the workpiece is securely clamped to prevent movement.
• Avoid overloading the tool. If the tool slows down significantly, reduce pressure.

6. Maintenance

Regular maintenance ensures the longevity and optimal performance of your angle grinder.

6.1 Cleaning

1. Always remove the battery pack before cleaning.
2. Keep the ventilation slots clean to prevent overheating. Use a soft brush or compressed air to clear dust and debris.
3. Wipe the tool housing with a damp cloth. Do not use harsh cleaning agents or solvents.

6.2 Disc Replacement

Refer to section 4.3 for detailed instructions on changing grinding discs.

6.3 Storage

1. Store the tool in a dry, secure place out of reach of children.
2. Remove the battery pack from the tool before storage.

7. Troubleshooting

This section addresses common issues you might encounter with your angle grinder.

• Tool does not start:
  • Check if the battery pack is properly inserted and charged.
  • Ensure the On/Off switch is fully engaged.
  • The tool may be in restart protection mode; release the switch and try again.
• Reduced power or overheating:
  • The battery may be low; recharge it.
  • Clean the ventilation slots to ensure proper airflow.
  • Reduce pressure on the workpiece to avoid overloading.
• Excessive vibration:
  • Check if the grinding disc is correctly mounted and tightened.
  • Inspect the disc for damage or imbalance; replace if necessary.

8. Specifications

9. Einhell Power X-Change Ecosystem

The Einhell TE-AG 18/115 Li is part of the innovative Power X-Change battery system. This means that any 18V Power X-Change battery can be used with this angle grinder, as well as with over 200 other tools and garden equipment in the Einhell range.

Figure 5: The Einhell Power X-Change battery at the center, surrounded by a wide array of compatible tools, illustrating the versatility of the battery system.

10. Warranty and Support

Einhell products are manufactured to high-quality standards and undergo strict quality controls. In the unlikely event of a problem, please contact your retailer or the Einhell customer service department. Keep your purchase receipt as proof of purchase for warranty claims.

For detailed warranty terms and conditions, or to find contact information for customer support, please refer to the official Einhell website or the documentation included with your product packaging.