Zippo 65828

Download PDF
Contents

Zippo Lighter Insert - Arc User Manual

Model: 65828

1. Introduction

The Zippo Lighter Insert - Arc is designed to provide a modern, windproof heat source for your Classic Zippo lighter case. This rechargeable insert features a double plasma arc beam, offering a reliable and flameless ignition. It is an ideal alternative to traditional fluid inserts, providing convenience and consistent performance.

Zippo Arc Lighter Insert

Image: The Zippo Arc Lighter Insert, a chrome-finished unit designed to fit into a classic Zippo lighter case, featuring the Zippo logo and specifications engraved on its side.

2. Safety Information

WARNING: KEEP OUT OF REACH OF CHILDREN.

To reduce the risk of injury, users must read this instruction manual thoroughly before operation. This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Do not expose to extreme temperatures or direct sunlight. This product is unsafe to carry on any flight.

Zippo Arc Lighter Insert Warning Label

Image: The bottom of the Zippo Arc Lighter Insert, displaying a clear warning label: "WARNING: KEEP OUT OF REACH OF CHILDREN. To reduce the risk of injury, users must read instructions manual."

3. Setup and Installation

  1. Prepare your Zippo Case: Open your Classic Zippo lighter case. If an existing insert is present, carefully remove it by pulling it out of the case.
  2. Insert the Arc Insert: Hold the Zippo Arc Lighter Insert with the ignition button facing the front of the lighter case. Gently slide the insert into the Zippo case until it is fully seated.
  3. Verify Fit: Ensure the insert fits snugly within the case. The insert is designed to fit all Classic Zippo lighter cases. It does not fit Slim or 1935 Replica cases.
Hand holding Zippo lighter with arc insert

Image: A hand holding a blue Zippo lighter case with the Arc Lighter Insert installed, demonstrating the proper fit and showing the activated plasma arc.

4. Charging Instructions

The Zippo Arc Lighter Insert is powered by a rechargeable 200 mAh IEC battery.

  1. Locate the USB Port: On the bottom of the insert, locate the micro USB port.
  2. Connect Charging Cable: Use the provided USB charging cable to connect the insert to a 5V 0.2A USB power source (e.g., computer USB port, wall adapter).
  3. Charging Indicator: A small LED indicator light will illuminate during charging. It will change color or turn off when fully charged.
  4. Charging Time: A full charge takes approximately 1 hour. The battery supports up to 300 charges.
Zippo Arc Lighter Insert USB port

Image: A close-up view of the Zippo Arc Lighter Insert's bottom, clearly showing the micro USB charging port and a small indicator light.

Zippo Arc Lighter Insert with USB cable connected

Image: The Zippo Arc Lighter Insert with its dedicated USB charging cable connected to the micro USB port, ready for charging.

5. Operating Instructions

  1. Open the Lid: Open the lid of your Zippo lighter case as you normally would.
  2. Ignite the Arc: Double tap the push-button ignition located on the top of the insert. Two plasma beams will cross to create the arc.
  3. Safety Feature: The arc will automatically shut off after 10 seconds as a safety feature. To re-ignite, simply double tap the button again.

6. Maintenance

  • Cleaning Electrodes: Periodically inspect the electrodes for any debris or buildup. Gently clean them with a dry, soft brush or cotton swab if necessary. Do not use abrasive materials or liquids.
  • Avoid Water: The insert is not waterproof. Avoid exposing it to water or other liquids.
  • Storage: When not in use for extended periods, store the insert in a cool, dry place.

7. Troubleshooting

ProblemPossible CauseSolution
Arc does not ignite.Low battery.Recharge the insert fully.
Arc does not ignite.Electrodes are dirty or obstructed.Clean the electrodes with a dry, soft brush.
Insert does not fit in case.Incorrect Zippo case type.Ensure you are using a Classic Zippo lighter case. This insert does not fit Slim or 1935 Replica cases.

8. Specifications

FeatureDetail
BrandZippo
Model NameZippo Lighter Insert - Arc
Part Number65828
MaterialZinc
ColorChrome
Item Weight1.76 ounces
Product Dimensions1.4"L x 0.5"W x 2.1"Th
Fuel TypeUSB Rechargeable
Battery200 mAh IEC
Input5V 0.2A micro USB port
Recharge TimeApproximately 1 hour
Charges per Battery300 charges
Safety Feature10 second time out
CompatibilityFits all Classic Zippo lighter cases (Does not fit Slim or 1935 Replica cases)
Country of OriginMade in China
UPC191693125832

9. Warranty Information

This Zippo Lighter Insert - Arc comes with a 2-year warranty. For detailed warranty terms and conditions, please refer to the official Zippo website or contact customer support.

10. Customer Support

For further assistance, technical support, or to inquire about replacement parts, please visit the official Zippo website or contact Zippo customer service directly. Refer to the contact information provided on the product packaging or the Zippo website.

© 2024 Zippo Manufacturing Company. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.