Duluth Forge Dual Fuel Ventless Gas Fireplace System

Introduction

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Duluth Forge Dual Fuel Ventless Gas Fireplace System. This system is designed to provide supplemental heat and aesthetic appeal to your living space, operating on either Natural Gas or Liquid Propane.

The Duluth Forge Ventless Fireplace System, Model DFS-300R-2AW, features a 26,000 BTU output, capable of heating up to 1,350 square feet. It includes a remote control for convenient operation and comes with 5 realistic hand-painted ceramic fiber logs within an antique white furniture-grade mantel.

Safety Information

WARNING: Improper installation, adjustment, alteration, service, or maintenance can cause injury or property damage. Read the installation, operating, and maintenance instructions thoroughly before installing or servicing this equipment.

• This appliance is vent-free and draws combustion air from the room. Ensure adequate ventilation.
• Equipped with an Oxygen Depletion Sensor (ODS) with automatic shut-off, which will turn off the unit if oxygen levels in the room fall below a safe threshold.
• Do not place clothing or other flammable materials on or near the appliance.
• Maintain a minimum clearance of 48 inches from the top of the fireplace to the ceiling.
• Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

What's Included

Your Duluth Forge Fireplace System package includes the following components:

• Fireplace Wood Mantel (Antique White) - Qty. 1
• Vent Free Fireplace Insert - Qty. 1
• Hand Painted Ceramic Fiber Logs - Qty. 5
• Remote Control - Qty. 1
• Receiver - Qty. 1
• AAA Battery - Qty. 3
• AA Battery - Qty. 4
• Hardware Pack - Qty. 1

Image: Duluth Forge Fireplace System with Antique White Mantel in a room setting.

Image: Close-up of the realistic hand-painted ceramic fiber logs.

Setup

1. Unpacking and Inspection: Carefully unpack all components and inspect for any damage. Report any damage to the retailer immediately.
2. Mantle Assembly: Some assembly of the furniture-grade mantel is required. Follow the detailed instructions provided in the separate assembly guide.
3. Placement: Position the fireplace system on a level, non-combustible surface. Ensure proper clearances from combustible materials as specified in the full installation manual. A minimum of 48 inches clearance from the top of the fireplace to the ceiling is required.
4. Fuel Connection: This dual-fuel system can operate on either Natural Gas or Liquid Propane. Ensure the correct fuel type is connected by a qualified professional. The unit is 99.9% efficient and does not require an outside duct or chimney.
5. Log Placement: Arrange the 5 ceramic fiber logs according to the diagram in the detailed manual to ensure optimal flame appearance and heat distribution.

Image: Diagram illustrating the dimensions of the fireplace and mantel.

Operating Instructions

1. Initial Ignition: Before first use, ensure all gas connections are secure and leak-free. Use the battery-assisted Piezo ignition system to light the pilot light as per the detailed instructions.
2. Remote Control Operation: The included remote control features an LCD screen and buttons for ON/OFF, MODE, and SET.
   • ON/OFF: Press to turn the fireplace burner on or off.
   • MODE: Toggle between manual operation and thermostat control.
   • SET: Adjust the desired temperature when in thermostat mode. The remote displays the current room temperature.
3. Manual Operation: In case the remote control is unavailable or batteries are depleted, the fireplace can be operated manually using the controls located on the unit. Refer to the full manual for specific instructions on manual ignition and flame adjustment.

Image: The remote control for the Duluth Forge fireplace system, showing ON, OFF, MODE, and SET buttons along with a temperature display.

Maintenance

• Cleaning: Ensure the fireplace is completely off and cool before cleaning. Use a soft, damp cloth to wipe down the exterior surfaces. Do not use abrasive cleaners.
• Log Care: The ceramic fiber logs are durable but can be fragile. Handle them with care. Do not clean them with water; use a soft brush to remove dust. Ensure logs are correctly positioned after any movement.
• Ventilation: Regularly check that the area around the fireplace is clear of obstructions to ensure proper airflow for combustion.
• Professional Inspection: It is recommended to have the fireplace inspected annually by a qualified service technician to ensure safe and efficient operation.

Troubleshooting

If you encounter issues with your fireplace system, refer to the following common troubleshooting steps. For more complex problems, consult the full manual or contact customer support.

• No Ignition: Check the fuel supply, ensure the pilot light is lit, and verify that the remote control batteries are functional.
• Pilot Light Won't Stay Lit: This could indicate an issue with the thermocouple or ODS sensor. Ensure the pilot flame is strong and engulfing the thermocouple.
• Inconsistent Flame: Check for proper log placement and ensure gas pressure is adequate.
• Remote Control Not Responding: Replace batteries in the remote and receiver. Ensure the receiver is set to 'Remote' mode.

Specifications

Warranty

This Duluth Forge Fireplace System comes with a Limited Warranty. Please refer to the warranty card included in your product packaging or visit the official Duluth Forge website for complete details regarding coverage, terms, and conditions.

Support

For further assistance, technical support, or to inquire about replacement parts, please contact Duluth Forge Customer Support. You can also visit the official Duluth Forge Store on Amazon for additional product information and resources.