Introduction
Welcome to the user manual for your CHACON 54671 Mini Remote Control Smart Plugs. This manual provides essential information for the safe and efficient operation of your device. Please read it thoroughly before use and retain it for future reference.
Package Contents
- 4 x CHACON Mini Remote Control Plugs
- 1 x Remote Control (with 1 CR2032 battery included)
- 1 x User Manual (this document)
Image: The CHACON set includes four mini remote control plugs and one remote control unit.
Important Safety Information
- For indoor use only.
- Do not exceed the maximum load of 2300W.
- Ensure the plugs are fully inserted into the wall socket.
- Do not immerse in water or expose to excessive moisture.
- Keep out of reach of children.
- Do not attempt to disassemble or repair the device.
Setup and Pairing
Your CHACON Mini Remote Control Plugs are pre-paired from the factory. If re-pairing is necessary or if you wish to change the assigned channel, follow these steps:
- Plug the mini remote control plug into a wall socket. The LED indicator on the plug will flash.
- Within 6 seconds of plugging in, press the desired "ON" button (1, 2, 3, or 4) on the remote control.
- The LED indicator on the plug will stop flashing and remain lit for a moment, then turn off, indicating successful pairing.
- Repeat for each plug and desired remote control channel.
Image: A single CHACON mini plug shown next to the remote control, illustrating the components involved in the pairing process.
Operation
The remote control allows you to switch connected devices ON and OFF wirelessly.
Using the Remote Control
- Each pair of "ON" and "OFF" buttons (1-4) corresponds to a specific plug.
- To turn a device ON: Press the corresponding "ON" button (e.g., "1 ON").
- To turn a device OFF: Press the corresponding "OFF" button (e.g., "1 OFF").
Manual Override
Each plug has a manual button on its side. Pressing this button will toggle the power state (ON/OFF) of the connected device.
Image: Close-up of the CHACON remote control, showing the numbered ON/OFF buttons.
Maintenance
Cleaning
Wipe the plugs and remote control with a dry, soft cloth. Do not use abrasive cleaners or solvents.
Remote Control Battery Replacement
The remote control uses one CR2032 battery.
- Locate the battery compartment on the back of the remote control.
- Open the compartment using a small screwdriver or coin.
- Remove the old battery and insert a new CR2032 battery, ensuring correct polarity (+/-).
- Close the battery compartment securely.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Plug does not respond to remote. | Not paired correctly. | Re-pair the plug with the remote control (see Setup section). |
| Plug does not respond to remote. | Remote control battery is low or dead. | Replace the CR2032 battery in the remote control. |
| Plug does not respond to remote. | Obstruction or distance. | Ensure the remote is within the 30m range and there are no major obstructions. |
| Device connected to plug does not turn on. | Device is faulty or switched off manually. | Check the device's power switch and ensure it is functioning correctly. |
| Plug LED does not light up. | No power to the wall socket. | Check the wall socket with another device. |
Image: A CHACON mini plug inserted into a wall socket, demonstrating typical installation.
Technical Specifications
- Brand: CHACON
- Model Number: 54671
- Color: White
- Dimensions (L x W x H): 7 x 6 x 6 cm
- Weight: 470 g (total for set)
- Material: Plastic
- Radio Frequency: 433.92 MHz
- Transmission Distance: Up to 30 meters (open field)
- Maximum Power: 2300W
- Power Source: Cable Electric (for plugs), 1 x CR2032 battery (for remote)
- Special Feature: Remote Controlled Outlets
Warranty and Support
For warranty information or technical support, please refer to the contact details provided by your retailer or visit the official CHACON website. Keep your proof of purchase for warranty claims.
