diymore SHT2000

Download PDF
Contents

diymore SHT2000 Digital Temperature and Humidity Controller User Manual

Model: SHT2000 | Brand: diymore

1. Introduction

The diymore SHT2000 AC 110~230V 10A Temperature and Humidity Controller is designed to provide precise control over environmental conditions. This versatile device can manage both temperature and humidity, making it suitable for a wide range of applications including domestic water heaters, freezers, refrigerators, aquariums, home brewing, chicken incubators, breeding, planting, and laboratory use.

It features a digital LED display for clear readings and offers distinct operating modes for heating, cooling, humidifying, and dehumidifying, ensuring optimal environmental management.

2. Specifications

Technical Parameters of SHT2000
ParameterValue
Product NameTemperature Humidity Controller
Product ModelSHT2000
Supply VoltageAC 110-230V
Power Supply Frequency50/60Hz
Temperature Range-20~60°C
Humidity Measurement Range0%~100%RH
Temperature Measurement Accuracy0.3 °C
Humidity Measurement Accuracy3%
Output ControlRelay Output
Output PowerMAX 10A
Product Dimensions1.97 x 1.57 x 0.79 inches
Item Weight4.87 ounces
SHT2000 Temperature Humidity Controller Parameters
Figure 2.1: SHT2000 Technical Parameters Overview.

3. Setup and Wiring

Proper wiring is crucial for the safe and effective operation of the SHT2000 controller. Please follow the instructions carefully. Note: There is no voltage output from the output terminal of the thermostat; the device needs to be connected to a separate power supply.

3.1. Power Connection

Connect the AC 110-230V power supply to terminals 1 and 2 on the controller. The controller is designed to work with alternating current, so the polarity of the wires (positive/negative) does not matter for these terminals. Ensure a secure connection to power the module.

diymore SHT2000 Controller with power cable and sensor
Figure 3.1: diymore SHT2000 Controller and components.

3.2. Sensor Connection

The temperature and humidity sensor connects to terminals 3, 4, 5, and 6. Refer to the diagram on the controller for the correct wire color-to-terminal mapping (Blue, Yellow, Green, Red). Ensure the sensor wires are stripped back slightly and securely fastened into their respective terminals.

High Quality Humidity Sensitive Capacitive Sensor
Figure 3.2: Close-up of the high-quality humidity sensitive capacitive sensor.

3.3. Device Connection (Heating/Humidifying/Cooling/Dehumidifying)

The SHT2000 provides relay outputs to control external devices such as heaters, humidifiers, fans, or dehumidifiers. These connections are made to terminals 7, 8, 9, and 10.

  • Heating/Cooling Control: Connect your heating or cooling device to terminals 7 and 8.
  • Humidifying/Dehumidifying Control: Connect your humidifying or dehumidifying device to terminals 9 and 10.

It is recommended to use a contactor to prevent overloading the controller, especially with high-power devices. Ensure all connections are secure and properly insulated.

SHT2000 Wiring Diagram for Temperature and Humidity Control
Figure 3.3: Detailed wiring diagram for the SHT2000 controller, showing connections for power, sensor, water heater, and humidifier.

4. Operating Instructions

The SHT2000 controller allows you to set precise start and stop values for both temperature and humidity to manage your environment effectively.

4.1. Temperature Setting (Heating & Cooling Modes)

To set the temperature parameters:

  1. Setting Start Temperature: Press and hold the ▲ (Up) button for 3 seconds until the Start Temperature value flashes. Use the ▲ or ▼ buttons to adjust the desired starting temperature.
  2. Setting Stop Temperature: Press and hold the ▼ (Down) button for 3 seconds until the Stop Temperature value flashes. Use the ▲ or ▼ buttons to adjust the desired stopping temperature.

The controller automatically determines the working mode based on your settings:

  • Heating Mode: If the Start Temperature is less than the Stop Temperature (Start Value < Stop Value). For example, to control a water heater, set it to heat to 65°C and stop, then restart heating if the temperature drops back to 50°C.
  • Cooling Mode: If the Start Temperature is greater than the Stop Temperature (Start Value > Stop Value). For example, in a farm setting, set a fan to ventilate until 26°C is reached and stop, then restart ventilation if the temperature rises to 30°C.

The display will return to the normal operating state after 5 seconds of inactivity.

SHT2000 Temperature Setting Guide
Figure 4.1: Visual guide for setting temperature parameters and understanding heating/cooling modes.

4.2. Humidity Setting (Humidifying & Dehumidifying Modes)

To set the humidity parameters:

  1. Setting Start Humidity: Press and hold the ▲ (Up) button for 3 seconds until the Start Humidity value flashes. Use the ▲ or ▼ buttons to adjust the desired starting humidity.
  2. Setting Stop Humidity: Press and hold the ▼ (Down) button for 3 seconds until the Stop Humidity value flashes. Use the ▲ or ▼ buttons to adjust the desired stopping humidity.

The controller automatically determines the working mode based on your settings:

  • Humidifying Mode: If the Start Humidity is less than the Stop Humidity (Start Value < Stop Value). For example, in a fresh supermarket, control a humidifier to start at 50% RH and stop humidifying at 80% RH.
  • Dehumidifying Mode: If the Start Humidity is greater than the Stop Humidity (Start Value > Stop Value). For example, in a workshop, control an exhaust dehumidification system to start at 70% RH and stop dehumidifying at 40% RH.

The display will return to the normal operating state after 5 seconds of inactivity.

SHT2000 Humidity Setting Guide
Figure 4.2: Visual guide for setting humidity parameters and understanding humidifying/dehumidifying modes.

5. Maintenance

To ensure the longevity and accurate performance of your diymore SHT2000 controller, regular maintenance is recommended:

  • Cleaning: Periodically wipe the exterior of the controller and the sensor with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
  • Sensor Care: Keep the sensor clean and free from dust, debris, or moisture buildup, especially in high-humidity environments. While the sensor is designed for various conditions, extreme or prolonged exposure to condensation may affect its accuracy over time.
  • Connection Check: Occasionally inspect all wiring connections to ensure they remain secure and free from corrosion.
  • Environmental Conditions: Operate the controller within its specified temperature and humidity ranges to prevent damage.

6. Troubleshooting

If you encounter issues with your SHT2000 controller, consider the following common troubleshooting steps:

  • No Power/Display:
    • Check if the power cable is securely connected to terminals 1 and 2.
    • Verify that the power source (AC 110-230V) is active.
    • Ensure the power supply frequency is 50/60Hz.
  • Inaccurate Readings:
    • Ensure the sensor is clean and free from obstructions.
    • Verify that the sensor wires are correctly connected to terminals 3, 4, 5, and 6 as per the diagram (Blue, Yellow, Green, Red).
    • Avoid placing the sensor directly in extreme conditions (e.g., direct sunlight, strong airflow, or excessive condensation) that might not represent the overall environment.
  • Device Not Activating (Heater/Humidifier/Fan):
    • Check the wiring of your external device to the controller's output terminals (7, 8 for heating/cooling; 9, 10 for humidifying/dehumidifying).
    • Verify that the set start and stop values are appropriate for the desired operation (e.g., for heating, Start Temp < Stop Temp).
    • Ensure the external device itself is functional and properly powered.
    • Confirm that the current draw of your device does not exceed the controller's MAX 10A output power.
  • Settings Not Saving:
    • Ensure you hold the respective button (Up for Start, Down for Stop) for 3 seconds until the value flashes, make your adjustment, and then wait for 5 seconds for the setting to be saved automatically.

If issues persist after following these steps, please contact diymore customer support for further assistance.

7. Warranty and Support

The diymore SHT2000 Digital Temperature and Humidity Controller comes with a standard return policy. For specific details regarding warranty coverage, returns, or replacements, please refer to your purchase documentation or the retailer's policy.

For technical support, product inquiries, or to explore other diymore products, please visit the official diymore store:

Visit the diymore Store

You may also find additional resources and FAQs on the diymore brand page or by contacting their customer service directly.

© 2024 diymore. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.