1. Introduction and Overview
The Ledvance Endura Pro Flood LED Outdoor Projector is a highly efficient, wall-mounted sensor floodlight designed for outdoor use. It features a wide beam angle and an innovative optical design, providing uniform surface illumination. Equipped with a motion detector, this projector offers enhanced security and convenience for various outdoor applications.
Key features include an adjustable lamp head for customized lighting, a robust IP55 protection rating for outdoor durability, and an IK05 impact resistance rating. This product is suitable for illuminating parking lots, squares, parks, and other exterior areas.
Figure 1: Ledvance Endura Pro Flood LED Projector packaging.
2. Safety Information
Please read all safety instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or other hazards.
- Electrical Safety: Installation must be performed by a qualified electrician in accordance with all local and national electrical codes. Ensure the power supply is disconnected before installation, maintenance, or repair.
- Outdoor Use: This product is designed for outdoor use with an IP55 rating, protecting against dust and low-pressure water jets. Do not submerge the product in water.
- Mounting: Mount the projector securely on a stable surface that can support its weight.
- Light Source: This luminaire contains a non-replaceable LED light source. Do not attempt to replace the LED module.
- Operating Temperature: Ensure the operating environment is within the specified temperature range to prevent overheating.
3. Package Contents
Verify that all components are present in the package:
- 1 x Ledvance Endura Pro Flood LED Projector with Motion Detector
- Mounting hardware (screws, wall plugs) - (Typically included, but check your specific package)
- Instruction Manual
4. Setup and Installation
Follow these steps for proper installation of your LED projector:
- Preparation: Disconnect power at the main circuit breaker before beginning installation. Choose a suitable mounting location on an outdoor wall, ensuring it is stable and provides the desired illumination coverage.
- Mounting: Use the provided mounting hardware to securely attach the projector to the wall. Mark the drilling points, drill holes, insert wall plugs, and then fasten the projector base.
- Wiring: Connect the electrical wires (Live, Neutral, Earth) from your power supply to the corresponding terminals on the projector. Ensure all connections are tight and properly insulated. Refer to the wiring diagram in the product packaging for specific details.
- Adjusting the Lamp Head: The lamp head is pivotable. Adjust its angle to direct the light beam to your desired area.
Figure 2: Product dimensions for installation planning.
5. Operating Instructions
The Ledvance Endura Pro Flood projector offers four selectable operating modes. These modes are typically set via controls located on the unit, often behind a cover or on the side panel.
Figure 3: Example of sensor and adjustment controls (actual appearance may vary).
5.1. Mode Selection
Refer to the markings next to the adjustment dials or switches on your specific unit to select one of the following modes:
- Permanent Light: The projector remains continuously illuminated, regardless of motion or ambient light levels.
- Standby: The projector may operate at a reduced brightness level (e.g., 20%) and switch to full brightness upon motion detection. This mode provides a constant low-level light for ambiance and security.
- Motion Activation: The projector turns on to full brightness only when motion is detected within its sensor range. It will turn off after a set delay if no further motion is detected.
- Dusk-to-Dawn: The projector automatically turns on at dusk and off at dawn, based on ambient light levels. Motion detection may still be active in this mode, triggering full brightness when needed.
5.2. Sensor Adjustments
Your projector typically includes controls for:
- Time Delay (TIME): Adjusts how long the light stays on after motion is detected.
- Sensitivity (SENS): Adjusts the detection range or sensitivity of the motion sensor.
- Lux Level (LUX): Sets the ambient light threshold at which the sensor becomes active (for dusk-to-dawn or motion modes).
Experiment with these settings to achieve optimal performance for your specific environment.
Figure 4: Motion detection in action, illuminating a path.
6. Maintenance
Regular maintenance ensures optimal performance and longevity of your projector.
- Cleaning: Periodically clean the lens and sensor window with a soft, damp cloth to remove dust, dirt, or debris that may obstruct light output or sensor function. Do not use abrasive cleaners or solvents.
- Inspection: Annually inspect the wiring and mounting hardware for any signs of wear, corrosion, or loosening. Tighten any loose screws and replace damaged components if necessary.
- No User Serviceable Parts: The LED light source is integrated and not user-replaceable. Do not attempt to open the housing or modify the internal components.
7. Troubleshooting
If you encounter issues with your projector, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply; faulty wiring; sensor settings incorrect; ambient light too high. | Check circuit breaker and power connections. Verify wiring. Adjust LUX setting to a lower value. Ensure motion is within sensor range. |
| Light stays on continuously. | Mode set to Permanent Light; continuous motion detected; sensor faulty. | Change operating mode. Check for constant movement in sensor range (e.g., tree branches). Clean sensor lens. |
| Light turns on randomly. | Sensor too sensitive; environmental factors (e.g., animals, heat sources, wind). | Reduce SENS setting. Reposition projector to avoid false triggers. |
| Light is dim or flickers. | Insufficient power; wiring issue; product defect. | Check power supply and wiring connections. If problem persists, contact customer support. |
If troubleshooting steps do not resolve the issue, contact customer support for further assistance.
8. Specifications
| Specification | Value |
|---|---|
| Brand | LEDVANCE |
| Model Number | 4058075228849 |
| Product Dimensions (L x W x H) | 20.1 x 5.6 x 22.5 cm |
| Item Weight | 480 g |
| IP Protection Rating | IP55 |
| Material | Polycarbonate (PC) |
| Power | 30 Watts |
| Luminous Flux | 3000 lm |
| Color Temperature | 4000 Kelvin |
| Average Lifespan | 50000 Hours |
| Style | With motion detector |
| Bulb Type | LED |
| Voltage | 230 Volts |
| Country of Origin | Germany |
9. Warranty and Support
This Ledvance Endura Pro Flood LED Projector comes with a 10-year guarantee, ensuring quality and reliability. For warranty claims or technical support, please retain your proof of purchase and contact your retailer or Ledvance customer service.
For additional information or assistance, please visit the official Ledvance website or consult your local dealer.
