Absima Racer 1:16 RC Electric Truggy User Manual

1. Introduction

Thank you for choosing the Absima Racer 1:16 RC Electric Truggy. This high-performance 4WD vehicle is designed for both beginners and experienced enthusiasts, offering thrilling speeds of over 35 km/h and robust off-road capabilities. This manual provides essential information to help you set up, operate, and maintain your Truggy for optimal performance and enjoyment.

What's in the Box:

• Absima Racer 1:16 RC Electric Truggy (100% assembled)
• 2.4Ghz Anti-interference Remote Control
• 2S 7.4V 500mAh Li-ion Battery
• USB Charging Cable

Image 1.1: The Absima Racer 1:16 RC Electric Truggy alongside its 2.4GHz remote control. The Truggy features a black and green body with large off-road tires, while the remote control is a pistol-grip style for precise handling.

2. Safety Precautions

To ensure safe operation and prevent damage to your Truggy or injury, please read and follow these safety guidelines:

• Always operate the Truggy in open areas away from people, pets, and obstacles.
• Do not operate near public roads, water, or in crowded areas.
• Keep hands, hair, and loose clothing away from moving parts.
• Never touch the motor or ESC immediately after use, as they can become very hot.
• Ensure the battery is fully charged before each use.
• Do not overcharge or short-circuit the battery.
• Store the Truggy and battery in a cool, dry place away from direct sunlight and heat sources.
• Adult supervision is recommended for users under 14 years of age.

3. Setup

3.1 Charging the Vehicle Battery

1. Connect the supplied USB charging cable to a USB power source (e.g., computer USB port, USB wall adapter).
2. Connect the other end of the USB charging cable to the 2S 7.4V 500mAh Li-ion battery.
3. The charging indicator on the USB cable will show the charging status (refer to charger's specific light indications).
4. Charging typically takes approximately 60-90 minutes. Do not leave charging unattended.

3.2 Installing Batteries in the Remote Control

1. Locate the battery compartment on the back of the remote control.
2. Open the battery compartment cover.
3. Insert 3 x 'AA' (LR6) batteries, ensuring correct polarity (+/-).
4. Close the battery compartment cover securely.

3.3 Installing the Vehicle Battery

1. Ensure the vehicle's power switch is in the 'OFF' position.
2. Open the battery compartment on the Truggy (usually located on the underside or top, secured by clips).
3. Carefully insert the charged Li-ion battery into the compartment.
4. Connect the battery connector to the vehicle's power connector, ensuring a secure fit.
5. Close the battery compartment cover.

Image 3.1: Detailed view of the Absima Racer Truggy's internal components, including the high-performance motor, electronic speed controller (ESC), and full-vehicle transmission bearings. The image also shows the remote control with labels for its functions and a diagram of the product packaging.

3.4 Binding the Remote Control to the Vehicle

The Truggy and remote control are typically pre-bound from the factory. If re-binding is necessary:

1. Turn on the remote control.
2. Turn on the Truggy.
3. The remote control and Truggy should automatically connect. If not, refer to the specific binding instructions in the full manual (if provided separately) or contact Absima support.

4. Operating Your Truggy

4.1 Remote Control Functions

• Steering Wheel: Turn left or right to control the Truggy's direction.
• Throttle Trigger: Pull to move forward, push to brake/reverse.
• Steering Trim: Adjusts the steering to ensure the Truggy drives straight when the steering wheel is centered.
• Throttle Trim: Adjusts the neutral point of the throttle.
• Speed Limit Switch: Allows you to limit the maximum speed of the Truggy, useful for beginners or indoor use.

4.2 Driving Tips

• Start slowly to get a feel for the controls before attempting high speeds.
• Practice steering and throttle control in an open area.
• Avoid sudden stops or turns at high speeds to prevent rollovers.
• Be mindful of battery life; performance will decrease as the battery drains.
• The Truggy features LED headlights for improved visibility in low-light conditions.

5. Maintenance

Regular maintenance will extend the life and performance of your Absima Racer Truggy.

• Cleaning: After each use, especially in dusty or dirty conditions, clean the Truggy with a soft brush or compressed air. Avoid using water directly on electronic components.
• Battery Care: Always disconnect the battery from the Truggy when not in use. Store the battery in a cool, dry place. Do not fully discharge the Li-ion battery; charge it before storing for extended periods.
• Inspections: Periodically check all screws, nuts, and connections to ensure they are tight. Inspect tires for wear and tear, and suspension components for damage.
• Lubrication: Lightly lubricate moving parts like universal joints and bearings as needed with RC-specific lubricant.

6. Troubleshooting

If you encounter issues with your Truggy, refer to the following common problems and solutions:

7. Specifications

8. Warranty and Support

Absima products are manufactured to high quality standards. For specific warranty information, please refer to the documentation included with your purchase or visit the official Absima website. If you require technical support, spare parts, or have any questions not covered in this manual, please contact Absima customer service or your local dealer.

Please retain your proof of purchase for warranty claims.