MYLEK Electric Fan Heater MY1400TE Instruction Manual

1. Introduction

This manual provides essential information for the safe and efficient operation of your MYLEK Electric Fan Heater, model MY1400TE. Please read these instructions carefully before installation and use, and retain them for future reference.

Image 1: Front view of the MYLEK Electric Fan Heater MY1400TE, showing its white casing and central digital display with control buttons.

2. Important Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all instructions before using this heater.
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.
• Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner.
• Do not use outdoors. This heater is designed for indoor use, specifically in bathrooms, with an IP24 splashproof rating.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
• To disconnect heater, turn controls to off, then remove plug from outlet.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• This heater includes an Overheat Protection feature. If the heater overheats, it will automatically shut off. If this occurs, unplug the heater, wait 30 minutes for it to cool, and then plug it back in.
• Ensure the heater is installed by a qualified electrician if hardwiring is required, or if you are unsure about the installation process.

3. Product Overview

The MYLEK Electric Fan Heater MY1400TE is a wall-mounted downflow heater designed for efficient heating in bathrooms and similar indoor spaces. It features a digital display, touch controls, and multiple programmable settings for user convenience and energy efficiency.

Key Features:

• Wall-Mounted Design: Space-saving and ideal for bathrooms.
• IP24 Splashproof Rating: Suitable for bathroom environments.
• Adjustable Temperature: Range from 5°C to 35°C.
• Heat Settings: Two power levels (1kW / 2kW).
• Digital Timer Programmes: 6 programmable settings, including a 7-day, 24-hour timer.
• Touch Screen Panel: Intuitive controls for easy operation.
• Intelligent Open Window Detection: Automatically switches off when a sudden temperature drop is detected, saving energy.
• Overheat Protection: Safety feature to prevent damage from excessive heat.
• Digital Room Temperature Display: Provides current room temperature.
• Frost Protection Function: Maintains a minimum temperature to prevent freezing.

Product Dimensions:

• Height: 38 cm
• Width: 28.5 cm
• Depth: 12 cm
• Weight: 2.21 kg

Image 2: The MYLEK Electric Fan Heater MY1400TE installed on a wall in a bathroom, demonstrating its compact and discreet design.

4. Installation and Setup

The MYLEK Electric Fan Heater is designed for wall mounting. Ensure the installation location is suitable for an IP24 rated appliance and away from direct water spray.

Installation Steps:

1. Choose Location: Select a suitable wall location in your bathroom, ensuring it is not directly above a bath or shower and allows for proper air circulation.
2. Mark Drilling Points: Use the provided mounting bracket as a template to mark the drilling points on the wall.
3. Drill Holes: Drill holes at the marked points and insert appropriate wall plugs (not supplied, choose based on wall material).
4. Secure Bracket: Attach the mounting bracket securely to the wall using screws.
5. Mount Heater: Carefully hang the heater onto the secured mounting bracket. Ensure it is firmly in place.
6. Power Connection: Connect the heater to a suitable power outlet. The heater operates on corded electric power. Note that the power cable is relatively short, and rewiring may be necessary for some installations; this should be performed by a qualified electrician.

Image 3: A detailed view of the mounting bracket on the rear of the MYLEK Electric Fan Heater MY1400TE, showing the attachment point for wall installation.

5. Operating Instructions

The MYLEK Electric Fan Heater features a user-friendly touch screen panel for all settings.

Image 4: A close-up of the MYLEK Electric Fan Heater MY1400TE's digital control panel, showing the power, mode, program, timer, and temperature adjustment buttons, along with the digital temperature display.

Control Panel Functions:

• Power Button (⏻): Turns the heater on or off.
• Mode Button (Mode): Cycles through different operating modes (e.g., Fan Only, 1kW Heat, 2kW Heat).
• Program Button (Prog): Accesses the programmable timer settings.
• Up/Down Arrows (▲ / ▼): Adjusts temperature settings, timer values, or navigates program options.
• Timer Button (Clock Icon): Sets the countdown timer for automatic shut-off.
• Digital Display: Shows current room temperature, set temperature, and active program/timer indicators.

Setting the Temperature:

1. Turn on the heater using the Power button.
2. Press the Up or Down arrow buttons to adjust the desired temperature. The display will show the set temperature, then revert to the current room temperature. The adjustable range is 5°C to 35°C.

Using the Timer and Programmes:

• The heater offers 6 digital timer programmes, including a 7-day, 24-hour timer.
• Press the Prog button to enter the programming menu.
• Use the Up/Down arrows to select and adjust daily or weekly heating schedules. Refer to the on-screen prompts for detailed programming steps.
• The Timer button can be used for a simple countdown timer function, typically for hourly increments.

Intelligent Open Window Detection:

This feature automatically detects a sudden drop in room temperature, indicating an open window or door. To conserve energy, the heater will temporarily switch off. It will resume operation once the temperature stabilizes or the feature is manually overridden.

6. Maintenance

Regular maintenance ensures the longevity and efficient operation of your heater.

• Cleaning: Before cleaning, always unplug the heater and allow it to cool completely. Use a soft, damp cloth to wipe the exterior surfaces. Do not use abrasive cleaners or solvents.
• Air Vents: Periodically check and clean the air intake and exhaust vents to ensure they are free from dust and debris. A vacuum cleaner with a brush attachment can be used.
• Storage: If storing the heater for an extended period, ensure it is clean and dry. Store it in a cool, dry place, preferably in its original packaging.

7. Troubleshooting

If you experience issues with your MYLEK Electric Fan Heater, refer to the following common problems and solutions:

• Heater does not turn on:
  • Check if the power cord is securely plugged into a working outlet.
  • Ensure the main power switch (if applicable) is in the 'ON' position.
  • Verify if the circuit breaker has tripped.
• Heater produces no heat:
  • Check the set temperature; it must be higher than the current room temperature.
  • Ensure the heater is not in 'Fan Only' mode.
  • The Overheat Protection may have activated. Unplug the heater, wait 30 minutes, and plug it back in.
  • The Open Window Detection may have activated due to a sudden temperature drop. Close windows/doors and allow the heater to resume.
• Heater is noisy:
  • Some fan noise is normal during operation.
  • Ensure the heater is securely mounted and not vibrating against the wall.
  • Check for any obstructions in the air vents.
• Digital display is not working:
  • Ensure the heater is powered on.
  • If the issue persists after checking power, contact customer service.

If the problem persists after attempting these troubleshooting steps, please contact MYLEK Customer Service.

8. Technical Specifications

9. Warranty and Customer Support

MYLEK is committed to providing excellent customer service. For any inquiries, technical support, spare parts, or warranty claims, please contact MYLEK Customer Service.

• Customer Service: Refer to your purchase documentation or the MYLEK website for contact details.
• Spare Parts: Spare parts support is available.
• Replacement Service: Next-day replacement delivery service may be available depending on your region and warranty terms.

Please retain your proof of purchase for warranty purposes.