Poagavgs 946-04396A

Download PDF
Contents

Poagavgs Pro-Parts 946-04396A Speed Selector Cable Instruction Manual

For Craftsman, MTD, Yard Machines, and Troy Bilt 2-Stage Snow Blowers

Introduction

This manual provides essential information for the installation, operation, maintenance, and troubleshooting of the Poagavgs Pro-Parts 946-04396A Speed Selector Cable. This component is designed as a replacement part for specific 2-stage snow blower models. Please read these instructions carefully before proceeding with installation or use to ensure proper function and safety.

Product Overview

The 946-04396A Speed Selector Cable is a critical component responsible for transmitting the speed selection input from the control lever to the snow blower's drive mechanism. It ensures the correct engagement of gears for forward and reverse motion.

Replacement Part Numbers:

  • 946-04396A
  • 746-04396A

Product Images:

Poagavgs Pro-Parts 946-04396A Speed Selector Cable, full view
Figure 1: Full view of the Poagavgs Pro-Parts 946-04396A Speed Selector Cable. This image displays the entire length of the cable, highlighting its black protective casing and the metal end fittings.
Close-up of Poagavgs Pro-Parts 946-04396A Speed Selector Cable ends
Figure 2: Close-up view of the end fittings on the speed selector cable. This image provides a detailed look at the metal connectors, one with an angled hook and the other with a mushroom-shaped head, which attach to the snow blower's control and drive mechanisms.

Compatibility

This speed selector cable is compatible with various 2-stage snow blower models from the following brands:

  • Craftsman
  • MTD
  • Yard Machines
  • Troy Bilt

Specific compatible models include, but are not limited to:

  • 31AH5ZLH704, 31AH6ZLG704, 31AM63LF704, 31AM62KE704
  • 31AH5ZLH304, 31AH5ZLH372, 31AH5ZLH401, 31AH5ZLH720, 31AH5ZLH730
  • 31AH5ZLH301, 31AH5ZLH709, 31AH5ZLH371, 31AH5ZLH307, 31AH5ZLH513
  • 31AH5ZLH713, 31AH5ZLH382, 31AH5ZLH000, 31AH5ZLH121, 31AH5ZLH205
  • 31AH5ZLH705, 31AH5ZLH706, 31AH5ZLH026, 31AH5ZLH726, 31AH5ZLH054
  • 31AH5ZLH745, 31AH5ZLH754, 31AH5ZLH029, 31AH5ZLH229, 31AH5ZLH134
  • 31AH5ZLH138, 31AH5ZLH729, 31AH5ZLH929, 31AH5ZLH129, 31AH5ZLH151

Always verify the part number on your existing cable or consult your snow blower's owner's manual to ensure correct fitment.

Installation

Safety First: Before beginning any repair, ensure the snow blower is turned off, the spark plug wire is disconnected, and the engine is cool. Wear appropriate safety gear, including gloves and eye protection.

General Installation Steps:

  1. Access the Cable: Locate the existing speed selector cable. This typically involves removing covers or panels to access the control lever and the transmission/friction plate area.
  2. Disconnect Old Cable: Carefully disconnect the old cable from both the speed selector lever and the transmission/friction plate. Note the routing of the cable for reinstallation.
  3. Install New Cable: Route the new 946-04396A cable in the same path as the old one, ensuring it does not get pinched or tangled.
  4. Connect Ends: Attach one end of the new cable to the speed selector lever and the other end to the transmission/friction plate. Ensure connections are secure. Note: Some users have reported needing to slightly file down one of the cable ends to fit through the selector lever hole. Proceed with caution if this is necessary.
  5. Adjust Tension: Most speed selector cables have an adjustment mechanism (e.g., a threaded barrel adjuster). Adjust the cable tension to ensure smooth and positive engagement of all speed settings. Refer to your snow blower's service manual for specific tensioning procedures.
  6. Test Functionality: Reconnect the spark plug wire. With the engine off, manually move the speed selector lever through all positions to confirm proper movement and engagement of the transmission. Start the engine and test at low speeds in a safe, open area.
  7. Reassemble: Replace any covers or panels removed during the installation process.

Operation

Once installed and properly adjusted, the speed selector cable allows you to change the ground speed of your 2-stage snow blower. Move the speed selector lever to the desired position (forward speeds, neutral, or reverse) to engage the corresponding gear. Ensure the lever clicks firmly into each position.

Maintenance

Regular maintenance can extend the life of your speed selector cable:

  • Inspection: Periodically inspect the cable for signs of wear, fraying, kinks, or damage to the outer casing. Check the end fittings for looseness or corrosion.
  • Lubrication: Apply a light lubricant (e.g., silicone spray or cable lubricant) to the cable ends and any exposed sections to ensure smooth operation and prevent corrosion.
  • Routing: Ensure the cable remains properly routed and is not rubbing against sharp edges or moving parts, which can cause premature wear.
  • Adjustment: If the speed selection becomes difficult or inconsistent, check and adjust the cable tension as needed.

Troubleshooting

  • Cable Does Not Fit:
    Symptom: Cable ends are too large or too small for the attachment points.
    Action: Double-check the snow blower model and the part number. Some users have reported needing to perform minor modifications, such as carefully filing down the sides of a fitting, to achieve proper fit. Ensure not to compromise the structural integrity of the fitting.
  • Cable Breaks Prematurely:
    Symptom: New cable snaps shortly after installation.
    Action: Inspect the cable routing for any sharp bends or points where the cable might be binding or under excessive stress. Ensure the cable is not overtightened during adjustment. Verify that the correct cable length and type are used for your specific snow blower model.
  • Difficulty Shifting/Incorrect Speed Selection:
    Symptom: Snow blower does not shift smoothly, or the selected speed does not engage correctly.
    Action: Check the cable tension. It may be too loose or too tight. Adjust the barrel adjuster until smooth and positive engagement is achieved for all speeds. Ensure all connections are secure and free of debris.
  • Cable Appears Flimsy or Different from Original:
    Symptom: The replacement cable seems thinner or less robust than the original equipment manufacturer (OEM) cable.
    Action: While this replacement cable is designed to function, variations in material thickness or design compared to OEM parts can occur. Ensure proper installation and regular maintenance to maximize its lifespan.

Specifications

Package Dimensions4.88 x 3.15 x 0.51 inches
Item Weight1.6 ounces

Warranty and Support

For warranty information or technical support regarding your Poagavgs Pro-Parts 946-04396A Speed Selector Cable, please contact the manufacturer directly through their official channels. Keep your purchase receipt as proof of purchase.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.