1. Introduction
The 509 Delta R3 Carbon Fiber Ignite Helmet is engineered for versatility and performance across various riding conditions. This manual provides essential information for the proper use, maintenance, and care of your helmet to ensure safety and longevity.
This helmet is designed to switch between three configurations: dual sport, full, and open, and features an Ignite heated shield for clear vision in challenging environments. Its carbon fiber construction contributes to its lightweight design.
2. Product Features
- Carbon Fiber Shell: Hand-laid carbon fiber shell for lightweight performance and durability.
- DOT Approved: Meets Federal Motor Vehicle Safety Standard 218 (FMVSS 218) for safety.
- Fidlock Magnetic Strap Clasp: Easy-to-use, glove-friendly magnetic buckle for secure fastening.
- Pro Series Liner and Cheekpads: Comes standard with new Pro Series Liner and Cheekpads for enhanced comfort.
- Dual Density EPS: Features dual density Expanded Polystyrene (EPS) for optimal fit and impact absorption.
- Ignite Heated Shield: Integrated heated shield system for fog-free vision in cold conditions.
- Multi-Configuration Design: Easily switch between dual sport, full, and open helmet configurations.
3. Safety Information
WARNING: This product can expose you to chemicals including Carbon Black, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
Always ensure the helmet fits properly and is securely fastened before riding. A helmet that is too loose or too tight can compromise its protective capabilities.
This helmet complies with US Federal Motor Vehicle Safety Standard 218 (FMVSS 218) (DOT FMVSS No. 218 Certified).
Proper Fitment
Refer to the size guide below to ensure proper fitment. A snug fit is crucial for safety.
| Brand Size | Head Circumference (in) | Hat Size (in) |
|---|---|---|
| XS | 20.9 - 21.1 | 6.6 - 6.8 |
| S | 21.6 - 21.9 | 6.9 - 7 |
| M | 22.5 - 22.6 | 7.1 - 7.3 |
| L | 23.3 - 23.5 | 7.4 - 7.5 |
| XL | 24 - 24.3 | 7.6 - 7.8 |
| 2XL | 24.8 - 25 | 8 |
| 3XL | 25.3 - 25.8 | 8.8 |
| 4XL | 26 - 26.3 | 9 |
| Youth Small | 18.1 - 18.9 | 6 |
| Youth Medium | 19.3 - 19.6 | 6.1 - 6.3 |
| Youth Large | 20 - 20.5 | 6.4 - 6.5 |
4. Setup
4.1 Initial Inspection
Upon unboxing, carefully inspect the helmet for any signs of damage. Ensure all components, including the visor, strap, and internal padding, are intact and properly seated.
4.2 Adjusting the Fit
Place the helmet on your head. It should feel snug around your cheeks and the top of your head without causing pressure points. The helmet should not move freely when you shake your head. If it does, consider a smaller size or adjusting the cheekpads if removable.
4.3 Securing the Fidlock Strap
The Fidlock magnetic strap buckle allows for quick and secure fastening. Bring the two parts of the buckle together; the magnets will guide them into place. Slide the strap through the adjuster to tighten until it is snug under your chin, allowing only one finger to fit between the strap and your chin. To release, slide the red tab away from the buckle.
4.4 Connecting the Ignite Heated Shield
Locate the power cord for the Ignite heated shield. Connect it to a compatible 12V power source on your vehicle. Ensure the connection is secure to prevent accidental disconnection during operation.
5. Operating the Helmet
5.1 Wearing the Helmet
Always wear the helmet correctly, ensuring it covers your forehead and the back of your head. The eyeport should provide a clear field of vision.
5.2 Utilizing the Ignite Heated Shield
Once connected to power, the Ignite heated shield will begin to warm, preventing fogging and ice buildup. This feature is particularly useful in cold and humid conditions. Ensure the shield is properly sealed against the helmet to maximize effectiveness and prevent air leaks.
5.3 Switching Configurations
The Delta R3 helmet offers three configurations: dual sport, full, and open. Refer to the diagrams below for instructions on how to convert your helmet between these modes. Typically, this involves removing or attaching the visor and/or the chin bar, depending on the desired configuration.
Figure 1: Helmet in Full Configuration. This image shows the helmet with the visor and chin bar attached, providing full face protection.
Figure 2: Helmet in Dual Sport Configuration. This view highlights the helmet's profile with the peak visor and face shield, suitable for both on-road and off-road use.
Figure 3: Helmet Rear View. This image displays the rear and side of the helmet, showcasing its carbon fiber finish and overall shape.
6. Maintenance
6.1 Cleaning the Helmet Shell
Clean the exterior of the helmet with a soft cloth and mild soap and water. Avoid harsh chemicals, solvents, or abrasive cleaners, as these can damage the carbon fiber finish and protective coatings. Rinse thoroughly and air dry.
6.2 Cleaning the Visor/Shield
The Ignite heated shield should be cleaned with a soft, damp cloth and mild soap. Do not use abrasive materials or harsh chemicals. For stubborn dirt, soak a soft cloth in warm water and place it over the affected area for a few minutes before gently wiping clean. Ensure the shield is completely dry before reconnecting power.
6.3 Liner and Cheekpad Care
The Pro Series Liner and Cheekpads are removable for cleaning. Hand wash them with mild soap and cool water. Air dry completely before reinserting them into the helmet. Do not machine wash or tumble dry.
6.4 Storage
Store your helmet in a cool, dry place away from direct sunlight and extreme temperatures. Use a helmet bag to protect it from dust and scratches when not in use.
7. Troubleshooting
7.1 Heated Shield Not Working
- Check the power connection to ensure it is securely plugged into both the helmet and the vehicle's 12V power source.
- Verify that the vehicle's 12V power source is active.
- Inspect the power cord for any visible damage or kinks.
7.2 Air Leaks Around Face Shield
Some users have reported air leaks around the face shield, particularly at higher speeds or in negative temperatures. To mitigate this:
- Ensure the face shield is fully closed and properly seated in its mechanism.
- Inspect the rubber seal around the shield for any damage, wear, or misalignment.
- If issues persist, contact 509 customer support for potential adjustments or replacement parts.
7.3 Helmet Feels Too Tight/Loose
- Refer to the size chart in Section 3 to confirm you have the correct size.
- New helmets may feel tight initially; the foam padding will compress slightly with use.
- Ensure the cheekpads are correctly installed. If the helmet is too loose, consider if smaller cheekpads are available or if the helmet size is incorrect.
8. Specifications
| Attribute | Detail |
|---|---|
| Brand | 509 |
| Model Name | Delta R3 Ignite Helmet |
| Item Model Number | F01005000-130-101 |
| Material | Carbon Fiber, Expanded Polystyrene (EPS) |
| Color | Red |
| Item Weight | 2 Pounds (approx. 0.91 kg) |
| Product Dimensions | 12 x 12 x 16 inches (approx. 30.5 x 30.5 x 40.6 cm) |
| Safety Rating | DOT Certified (Meets FMVSS 218) |
| Closure Type | Magnetic (Fidlock) |
| Shell Type | Hard |
| Finish Type | Matte |
| Sport | Motorcycling |
| UPC | 843614120890 |
9. Warranty and Support
Specific warranty details for the 509 Delta R3 Carbon Fiber Ignite Helmet are typically provided with the product packaging or available on the official 509 website. Please retain your proof of purchase for warranty claims.
For technical support, parts, or warranty inquiries, please contact 509 customer service directly. Visit the official 509 website for contact information and the most up-to-date support resources.
Official Brand Store: 509 Store on Amazon
10. Official Product Videos
No official product videos from the seller were found in the provided data. Please refer to the manufacturer's official website or authorized channels for any available video content related to this product.
