1. Setup Instructions
The APPS2Car 3-in-1 Magnetic Car Phone Mount offers versatile installation options for your dashboard, windshield, or air vent. Please follow these instructions carefully for optimal performance and secure attachment.
1.1 Dashboard/Windshield Mount Installation
- Clean the Surface: Thoroughly clean the desired mounting surface on your dashboard or windshield with an alcohol wipe and let it dry completely. Ensure the surface is smooth and free of dust or oils.
- Apply 3M VHB Pad (Dashboard Only): For dashboard mounting, apply the included 3M VHB sticky dashboard pad to the cleaned surface. Press firmly for several seconds.
- Attach Suction Cup: Place the industrial-strength sticky gel suction cup base onto the 3M VHB pad (or directly onto the clean windshield). Press down firmly to remove air, then push the lever down to lock the suction cup in place.
- Curing Time: Allow the adhesive on the 3M VHB pad to cure for at least 24 hours before attaching the magnetic phone holder or placing a phone on it. This ensures maximum adhesion.

Figure 1: Suction cup installation steps, including cleaning the surface and pressing down the suction cup.

Figure 2: The suction cup mount demonstrating its strong hold by supporting a 15-pound bowling ball.
Video 1: Demonstrates the installation process for both the air vent and dashboard magnetic car phone mount.
1.2 Air Vent Mount Installation
- Attach Air Vent Clip: Secure the air vent clip to a suitable horizontal or vertical air vent blade.
- Tighten Lock: Twist the nut on the air vent clip to firmly clamp it onto the vent blade, ensuring a stable base.
- Attach Magnetic Head: Connect the magnetic phone holder head to the air vent clip.

Figure 3: The dual mounting system, illustrating both dashboard suction cup and air vent clip options.

Figure 4: Illustrates compatibility of the air vent mount with 99% of horizontal air vents.
2. Operating Instructions
2.1 Attaching Your Phone
- Apply Metal Plate: Attach one of the included metal plates to the back of your phone or inside your phone case. For wireless charging phones, place the metal plate away from the charging coil area to avoid interference.
- Magnetic Attachment: Simply bring your phone close to the magnetic head of the mount. The powerful N52 magnets will securely hold your phone in place.

Figure 5: Demonstrates the strong magnetic force and ease of one-hand operation when attaching a phone.

Figure 6: Illustrates various metal plate placement options, including considerations for wireless charging.
2.2 Adjusting the View Angle
- 360-Degree Rotation: The swivel ball joint allows for 360-degree rotation, enabling you to position your phone in portrait or landscape mode.
- Telescopic Arm: The telescopic arm can be extended from 4.13 inches to 5.75 inches. Adjust the arm by pushing or pulling it to achieve your desired distance.
- Locking Knob: Use the screw-nut lock to secure the magnetic mount's position and prevent unwanted movement, ensuring an optimal viewing angle.

Figure 7: The adjustable telescopic arm, showing its extension range from 4.13 to 5.75 inches.

Figure 8: Details the 360-degree swivel ball joint and the secure tightening knob for optimal viewing.
2.3 One-Hand Operation
The magnetic design allows for effortless one-hand attachment and detachment of your phone, promoting safer driving by minimizing distraction.

Figure 9: Illustrates the convenience of one-hand operation for attaching the phone to the magnetic mount.
3. Maintenance
- Cleaning the Suction Cup: If the suction cup loses its stickiness, rinse it with warm water and let it air dry. Do not use harsh chemicals or abrasive materials.
- Cleaning Surfaces: Periodically clean the dashboard or windshield surface where the mount is attached to ensure optimal adhesion.
- Checking Security: Regularly check that all components are securely fastened and that the mount remains stable.
4. Troubleshooting
- Mount not sticking to dashboard/windshield:
a. Ensure the surface is clean, dry, and smooth. Textured or porous surfaces may reduce adhesion.
b. For dashboard mounting, ensure the 3M VHB pad has cured for at least 24 hours before use.
c. Re-apply the suction cup, pressing firmly to expel all air before locking the lever. - Phone not holding securely:
a. Verify that the metal plate is correctly positioned on your phone or inside the case, aligning with the magnetic head.
b. Extremely thick phone cases may reduce magnetic strength. Consider a thinner case or placing the metal plate on the outside of the case. - Mount detaches in high heat:
a. High temperatures can affect adhesive performance. Ensure the dashboard surface is as clean as possible and consider re-applying the 3M VHB pad if necessary.
b. For windshield mounting, ensure the suction cup is clean and re-applied firmly.
5. Product Specifications
| Feature | Detail |
|---|---|
| Brand | APPS2Car |
| Model Name | APPS2Car 3-in-1 Car Phone Mount |
| Model Number | APPS2Car 3-in-1 Car Phone Mount |
| Mounting Type | Vent, Dashboard, Windshield |
| Compatible Devices | Smartphones |
| Compatible Phone Models | iPhone 16/16 Plus/16 Pro/16 Pro Max/15/15 Plus/15 Pro/15 Pro Max/14/14Plus/14 Pro/14 Pro Max/13 Pro Max/13 Pro/13/13 Mini/12 Pro Max/12 Pro/12/12 Mini/11 Pro Max/11 Pro/11/XS Max/XS/XR/X/10/8+/8/7+/7/6S+/6S/6+/6; Samsung Galaxy S22/Ultra S22+/S21+/S21/S20/S20+/S10/S10+/S10e/S9/S9+/S8/S8+/S7/S6/S5/S4/S3/S2/S1, Galaxy Note 20/Ultra 20/10/9/8, Galaxy A9S/A9/A8S/A8+, Google Pixel 6Pro 6/5a/5/4/4XL/4a, Google Pixel etc. all smartphones |
| Additional Features | Built-in 6x N52 Powerful Magnets. Strong Stick Gel Suction Cup Base, 360-degrees Adjustable, One-hand Operation, Telescopic arm no need to screw to adjust. |
| Weight Capacity Maximum | 350 Grams |
| Item Weight | 0.24 Kilograms |
| Material | Acrylonitrile Butadiene Styrene |
6. Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact APPS2Car customer service directly. Keep your purchase receipt for any warranty claims.