1. Introduction
This manual provides instructions for the safe and effective use of your Invigorated Water pH Recharge Glass Alkaline Water Filter Dispenser. Please read all instructions carefully before assembly and operation. Retain this manual for future reference.
2. Safety Information
- Handle the glass vessel with care to prevent breakage.
- Do not place the dispenser near heat sources or in direct sunlight for prolonged periods.
- Ensure the bamboo stand is assembled securely on a stable, flat surface.
- Do not use abrasive cleaners or harsh chemicals on any part of the dispenser.
- This product is not dishwasher safe. Hand wash all components.
- Keep out of reach of children.
3. Package Contents
Verify that all components are present before assembly:
- Glass Water Vessel (8.5L / 2.25 Gallons capacity)
- Bamboo Lid
- Bamboo Wood Stand (multiple pieces for assembly)
- pH001 Multi-stage Alkaline Water Filter
- Filter Housing
- Spigot (with washers and nut)
- Instruction Manual
Figure 1: Exploded view showing the glass vessel, bamboo lid, filter, filter housing, spigot, and bamboo stand.
4. Setup Instructions
4.1. Assemble the Bamboo Stand
- Unpack the bamboo stand components.
- Align the stand pieces and secure them according to the provided diagram, ensuring a stable base. A Phillips screwdriver may be required to tighten screws for stability.
4.2. Install the Spigot
- Ensure the rubber washer is correctly positioned on the spigot's threaded shaft.
- Insert the spigot through the hole in the glass vessel from the outside.
- Place the second rubber washer on the threaded shaft from the inside of the vessel.
- Secure the spigot by hand-tightening the nut onto the threaded shaft from the inside. Do not overtighten.
4.3. Prepare the Filter
- Submerge the pH001 filter in water for approximately 10-15 minutes.
- Rinse the filter under running tap water for 1 minute to remove any loose particles.
4.4. Install the Filter
- Place the prepared filter into the filter housing.
- Insert the filter housing with the filter into the top section of the glass vessel. Ensure it sits flush and securely.
4.5. Initial Flushing
- Fill the top section of the dispenser with tap water.
- Allow the water to filter through and dispense the entire volume. Discard this water.
- Repeat this flushing process two more times (total of three full flushes) to ensure the filter is primed and any residual particles are removed.
Figure 2: Fully assembled pH Recharge Glass Alkaline Water Filter Dispenser.
5. Operating Instructions
5.1. Filling the Dispenser
After initial setup, fill the top section of the dispenser with tap water. The water will slowly filter through the pH001 filter into the main glass vessel.
5.2. Dispensing Water
Once the water has filtered into the main vessel, use the spigot to dispense purified alkaline water. The dispenser has an 8.5L (2.25 Gallon) capacity.
Figure 3: The pH001 filter performs two main steps: filtration of contaminants and mineralization to increase pH.
Figure 4: Multi-stage filter layers, including micro net, granular activated carbon, ion exchange resin, ORP/Maifan/Tourmaline balls, and Zeolite/PP layer, designed to remove various heavy metals and impurities.
6. Maintenance
6.1. Filter Replacement
The pH001 filter has a capacity of up to 1000 liters (264 gallons) or approximately 3-4 months of use for 3-4 people. Replace the filter regularly to maintain optimal water quality and filtration performance.
Figure 5: Recommended filter replacement schedule based on household size.
Figure 6: One filter can replace approximately 750 plastic water bottles, contributing to waste reduction.
6.2. Cleaning the Dispenser
Regularly clean the glass vessel, bamboo lid, and spigot with mild soap and warm water. Rinse thoroughly and dry completely before reassembly. Do not use abrasive sponges or cleaners that could scratch the glass or damage the bamboo finish. The dispenser is not dishwasher safe.
7. Troubleshooting
- Slow Filtration: If filtration is unusually slow, ensure the filter has been properly soaked and rinsed as per setup instructions. A clogged filter may also indicate it's time for replacement.
- Leaking Spigot: Check that both rubber washers are correctly positioned on either side of the glass vessel and that the nut is securely tightened. Avoid overtightening, which can damage the washers.
- Unusual Taste: Ensure the initial flushing steps were completed. If an unusual taste persists, the filter may need further rinsing or replacement.
- Water Not Alkaline: Verify that the pH001 filter is correctly installed and has been properly prepared. Filter performance can decrease over time, indicating a need for replacement.
8. Specifications
| Brand | Invigorated Water |
| Model Number | pH RECHARGE Glass - US |
| Material | Glass, Bamboo |
| Capacity | 8.5 Liters (2.25 Gallons) |
| Product Dimensions | 11.1"L x 17"W x 10.9"H |
| Item Weight | 8.4 Pounds |
| Filter Type | pH001 Multi-stage Alkaline Water Filter |
| Dishwasher Safe | No |
Figure 7: Product dimensions for placement reference.
9. Warranty Information
Invigorated Water products are covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Invigorated Water website.
10. Customer Support
For further assistance, troubleshooting, or to purchase replacement filters, please contact Invigorated Water customer support. Contact details can typically be found on the product packaging or the official Invigorated Water website.
