Maxxima LED Slide Dimmer Switch User Manual

1. Introduction

Thank you for choosing the Maxxima LED Slide Dimmer Switch. This product is designed to provide smooth and reliable dimming for a variety of lighting loads, including incandescent, dimmable LED, and CFL bulbs. It supports both single pole and 3-way circuit configurations, offering flexibility for your lighting control needs. Please read this manual thoroughly before installation and use to ensure proper operation and safety.

2. Safety Information

WARNING: To avoid fire, shock, or death; turn off power at circuit breaker or fuse and test that power is off before wiring! This device must be installed in accordance with all national and local electrical codes.

• For indoor use only.
• Do not use with non-dimmable lighting fixtures.
• Not for use with ceiling fans or motor loads.
• Ensure the total wattage of connected bulbs does not exceed the dimmer's maximum rating (600W Incandescent; 200W Dimmable LED/CFL).
• If you are unsure about any part of these instructions, consult a qualified electrician.

3. Package Contents

• Maxxima LED Slide Dimmer Switch (Model: MEW-DM650)
• Screwless Wall Plate
• Mounting Screws
• Wire Nuts

4. Setup and Installation

This dimmer switch is compatible with both single pole and 3-way wiring configurations. In a 3-way circuit, only one dimmer may be used; the second switch must be an ON/OFF only switch.

4.1 Wiring Diagram

Refer to the following image for typical wiring connections. Always ensure power is OFF before beginning any wiring.

4.2 Installation Steps

1. Turn off Power: At the circuit breaker or fuse box, turn off the power to the switch location. Verify power is off using a voltage tester.
2. Remove Old Switch: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch.
3. Identify Wires: Identify the LINE (hot), LOAD, and GROUND wires. For 3-way installations, also identify the TRAVELER wires.
4. Connect Wires: Connect the wires from the wall box to the dimmer switch using the provided wire nuts.
   • Black wire on dimmer: Connect to LINE (hot) wire.
   • Red wire(s) on dimmer: Connect to LOAD wire (and TRAVELER wire for 3-way).
   • Green wire on dimmer: Connect to GROUND wire.
5. Mount Dimmer: Carefully push the wired dimmer switch into the wall box. Secure it with the provided mounting screws.
6. Attach Wall Plate: Snap the screwless wall plate onto the dimmer switch.
7. Restore Power: Turn the power back on at the circuit breaker.

4.3 Sensitivity Adjustment (Trim Dial)

The dimmer features a trim dial located underneath the cover plate. This dial allows you to adjust the low-end dimming range to ensure optimal compatibility with various LED and CFL lamps, preventing flicker or premature turn-off at low light levels.

To adjust: Remove the screwless wall plate. Locate the small trim dial at the bottom of the dimmer. Turn the dial clockwise to increase the minimum light level or counter-clockwise to decrease it, until stable dimming is achieved without flicker.

5. Operating Instructions

The Maxxima LED Slide Dimmer Switch features a vertical slide control for dimming and a separate ON/OFF button.

• Turn ON/OFF: Press the bottom button to turn the lights ON or OFF.
• Dimming: Move the vertical slide control up to increase light brightness and down to decrease light brightness.

6. Maintenance

The Maxxima LED Slide Dimmer Switch requires minimal maintenance. To clean, simply wipe the surface with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish.

7. Troubleshooting

• Lights flicker or do not dim properly: Adjust the sensitivity trim dial (refer to Section 4.3). Ensure your bulbs are dimmable LED or CFL, or incandescent.
• Lights do not turn on: Check the circuit breaker. Verify all wiring connections are secure. Ensure the dimmer is not connected to a non-dimmable fixture.
• Dimmer does not work with low wattage LED loads: The dimmer may not be compatible with LED loads of 4.5 watts or less. Consider increasing the total wattage of connected LED bulbs.
• Dimmer gets warm: It is normal for dimmers to feel warm during operation. If it becomes excessively hot or emits a burning smell, immediately turn off power at the circuit breaker and consult a qualified electrician.
• Not for use with ceiling fans: This dimmer is designed for lighting loads only and should not be used to control ceiling fans or other motor-driven appliances.

8. Specifications

9. Warranty and Support

The Maxxima LED Slide Dimmer Switch comes with a 1-year warranty from the date of purchase, ensuring safety and reliability. This warranty covers defects in materials and workmanship under normal use.

For technical support, troubleshooting assistance, or warranty claims, please contact Maxxima customer service. Refer to the product packaging or the Maxxima website for the most current contact information.