TIMBERTECH ABPST07 Airbrush Compressor User Manual

1. Introduction

Thank you for choosing the TIMBERTECH ABPST07 Airbrush Compressor. This powerful, portable, and quiet 1/6 HP compressor is designed for a wide range of applications, including airbrush painting, nail art, temporary tattoos, cake decorating, craft painting, model art, and automotive graphics. This manual provides essential information for the safe and efficient operation, setup, and maintenance of your new airbrush compressor.

Please read this manual thoroughly before initial use and retain it for future reference.

2. Important Safety Instructions

To ensure safe operation and prevent injury or damage, always observe the following safety precautions:

• Always operate the compressor in a well-ventilated area.
• Ensure the power supply voltage matches the compressor's requirements (110-120V/60Hz).
• Do not operate the compressor near flammable liquids or gases.
• Keep children and pets away from the operating area.
• Disconnect the power cord before performing any maintenance or when the compressor is not in use.
• This air compressor is designed for airbrush use only. Do not connect it to spray guns or other high-demand air tools.
• Avoid touching hot surfaces during or immediately after operation.
• Always wear appropriate personal protective equipment, such as safety glasses, when operating the airbrush system.

3. Package Contents

Verify that all items are present in the package:

• 1 x TIMBERTECH ABPST07 Air Compressor
• 1 x Instruction Manual

4. Product Overview

The TIMBERTECH ABPST07 Airbrush Compressor features a compact design with advanced functionalities for consistent performance.

Figure 1: Overall view of the TIMBERTECH ABPST07 Airbrush Compressor, showcasing its compact design, pressure regulator, and carrying handle.

Key Features:

• Cool-Down Fan: Integrated fan to reduce operating temperature and extend the compressor's lifespan.
• Oil-less Piston Type: Ensures no oil pollution in the air source, making it suitable for sensitive applications.
• Automatic Stop Function: The compressor automatically stops when air is not being used (at 4 bar / 58 PSI) and restarts when air is demanded (at 3 bar / 43 PSI), conserving energy and reducing noise.
• Pressure Regulator with Gauge: Allows precise control and monitoring of air pressure output.
• Water Trap and Air Filter: Removes moisture and impurities from the air, protecting your airbrush and artwork.
• Suction Pad Feet: Provides stability and reduces vibration during operation.

Figure 2: Illustration of the compressor's double heat dissipation system, highlighting the efficient fin design and the cooling fan for extended operation.

Figure 3: Close-up view of the suction pad feet, designed to enhance stability and minimize noise by reducing micro-shifts during operation.

5. Setup

Follow these steps for initial setup:

1. Unpack: Carefully remove the compressor from its packaging.
2. Placement: Place the compressor on a stable, level surface in a well-ventilated area. Ensure the suction pads are firmly attached to the surface.
3. Connect Air Hose: Connect your airbrush hose to the 1/8 BSP connection on the pressure regulator. Ensure a secure, airtight connection.
4. Power Connection: Plug the power cord into a grounded electrical outlet (110-120V/60Hz).

6. Operating Instructions

Operating your TIMBERTECH ABPST07 compressor is straightforward:

1. Power On: Press the power switch to the 'ON' position. The compressor will start to build pressure.
2. Adjust Pressure: To adjust the air pressure, first pull up the knob on the pressure regulator. Then, rotate the knob clockwise to increase pressure or counter-clockwise to decrease pressure. Read the desired pressure from the gauge. Once set, push the knob down to lock the setting.

Figure 4: Instructions for adjusting the air pressure: Pull the knob up, rotate to the desired setting shown on the gauge, then push down to lock.

Figure 5: The compressor features a simple one-button start and an integrated pressure gauge for real-time monitoring of working pressure.

3. Automatic Stop/Start: The compressor will automatically stop when the pressure reaches approximately 4 bar (58 PSI) and restart when the pressure drops to approximately 3 bar (43 PSI). This maintains a consistent air supply and reduces wear.

Figure 6: Diagram illustrating the automatic start (3 bar / 43 PSI) and stop (4 bar / 58 PSI) function, ensuring stable air pressure.

4. Begin Airbrushing: Once the desired pressure is set, you can begin using your airbrush.
5. Power Off: When finished, turn off the compressor using the power switch and disconnect it from the power outlet.

7. Maintenance

Regular maintenance ensures optimal performance and longevity of your compressor.

• Drain Water Trap: After each use, or when moisture is visible, drain the water from the water trap. To do this, ensure the compressor is off and depress the drain button at the bottom of the water trap.

Figure 7: To drain accumulated water, press the button located at the bottom of the water trap. Do not perform this while the machine is working or under pressure.

• Clean Air Filter: Periodically check and clean the air filter element in the water trap. Replace if heavily soiled or damaged.
• General Cleaning: Wipe down the exterior of the compressor with a damp cloth. Do not use harsh chemicals or abrasive cleaners.
• Storage: Store the compressor in a clean, dry environment when not in use.

8. Troubleshooting

Refer to the table below for common issues and their solutions:

9. Technical Specifications

Detailed specifications for the TIMBERTECH ABPST07 Airbrush Compressor:

10. Warranty and Support

For warranty information and customer support, please refer to the documentation provided with your purchase or contact the retailer/manufacturer directly. Keep your proof of purchase for any warranty claims.

Manufacturer: Airgoo Pneumatic B.V.