Introduction
The Henry Xtra 160 HVX160 is a versatile and powerful canister vacuum cleaner designed for efficient cleaning of various surfaces. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Henry Xtra 160 vacuum.
Figure 1: The NaceCare Henry Xtra 160 Canister Vacuum with hose and floor tool.
Key Features:
- Powerful 680 watt motor (0.9 HP) for strong suction.
- Includes Turbo Brush for effective carpet cleaning and hair pickup.
- Specialist hard-floor tool for optimal performance on hard surfaces.
- MicroTex filters provide 99.97% filtration down to 0.3 micron for improved air quality.
- Large 1.6 gallon capacity for extended cleaning sessions.
- Whisper quiet operation, suitable for various environments.
- Self-seal tab on bags for dust-free emptying.
- Convenient on-board accessory storage.
Important Safety Information
Always read and understand all safety warnings and instructions before using the appliance. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
- Do not use the appliance if the power cord or plug is damaged.
- Do not pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Do not allow children to operate the vacuum cleaner.
- Always unplug the vacuum cleaner before performing any maintenance or cleaning.
- Ensure all filters are correctly installed before operation.
Setup and Assembly
1. Unpacking:
Carefully remove all components from the packaging. Retain packaging for future storage or transport. Verify that all parts listed in the "What's in the Box" section are present.
2. Attaching the Hose:
- Locate the flexible hose.
- Insert the hose cuff into the suction inlet on the front of the vacuum unit until it clicks securely into place.
3. Assembling the Wand and Floor Tool:
- Connect the two chrome wand sections together.
- Attach the curved handpiece to the top of the assembled wand.
- Select the desired floor tool (Turbo Brush for carpets or hard-floor tool for hard surfaces).
- Attach the chosen floor tool to the bottom of the assembled wand.
- Insert the curved handpiece into the end of the flexible hose.
Figure 2: The Henry Xtra 160 vacuum shown with its comprehensive accessory kit, including hose, wands, and various floor tools.
4. Installing the Dust Bag:
The Henry Xtra 160 uses disposable dust bags. Ensure a bag is correctly installed before operation.
- Unclip and remove the motor head from the canister.
- Ensure the MicroTex filter is properly seated.
- Slide the cardboard collar of a new dust bag onto the inlet tube inside the canister. Ensure the bag is fully open and positioned correctly within the canister.
- Replace the motor head, ensuring it is securely clipped.
Operation
1. Powering On/Off:
Plug the power cord into a suitable electrical outlet. The Henry Xtra 160 features an automatic cord rewind system. To operate, press the red ON/OFF switch located on the top of the motor head.
2. Using the Floor Tools:
- Turbo Brush: Ideal for carpets and picking up pet hair. The air-driven brush agitates carpet fibers for deeper cleaning.
- Hard-Floor Tool: Designed for optimal suction and maneuverability on hard surfaces such as wood, tile, and laminate.
Figure 3: The Henry Xtra 160's Turbo Brush effectively cleaning a carpeted surface.
Figure 4: The Henry Xtra 160's hard-floor tool efficiently cleaning debris from a tiled floor.
3. Using Accessories:
The Henry Xtra 160 comes with a variety of accessories for different cleaning tasks. These can be attached directly to the curved handpiece or the wand.
- Crevice Tool: For narrow spaces, corners, and edges.
- Dusting Brush: For delicate surfaces, shelves, and upholstery.
- Upholstery Nozzle: For furniture and fabric surfaces.
Maintenance
Regular maintenance ensures optimal performance and extends the life of your Henry Xtra 160 vacuum.
1. Replacing the Dust Bag:
Replace the dust bag when it is full or when suction power noticeably decreases. The self-seal tab on the bag ensures dust-free disposal.
- Unplug the vacuum cleaner from the power outlet.
- Unclip and remove the motor head.
- Carefully pull the cardboard collar of the full dust bag off the inlet tube. Use the self-seal tab to close the bag opening.
- Dispose of the full bag responsibly.
- Install a new dust bag as described in the "Setup and Assembly" section.
- Replace the motor head.
2. Cleaning the Filters:
The MicroTex filter provides excellent filtration. Periodically check and clean the filter to maintain suction and air quality.
- Unplug the vacuum.
- Remove the motor head.
- Gently remove the MicroTex filter.
- Tap the filter gently over a waste bin to dislodge dust. Do not wash the filter unless specified by the manufacturer.
- Reinstall the filter, ensuring it is correctly seated before replacing the motor head.
3. Cleaning the Turbo Brush:
Hair and debris can become tangled around the brush roll. Regularly inspect and clean the brush roll for optimal performance.
- Unplug the vacuum and detach the Turbo Brush from the wand.
- Using scissors, carefully cut away any tangled hair or threads from the brush roll.
- Remove the debris.
4. General Cleaning:
Wipe the exterior of the vacuum with a damp cloth. Do not use abrasive cleaners or solvents.
Troubleshooting
If you encounter issues with your Henry Xtra 160, refer to the table below for common problems and their solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Vacuum does not turn on. | No power supply. Power switch off. | Check if the plug is securely in the outlet. Ensure the ON/OFF switch is pressed. Check household fuse/circuit breaker. |
| Loss of suction. | Full dust bag. Clogged hose/wand/tool. Dirty filter. | Replace the dust bag. Check and clear any blockages in the hose, wand, or floor tool. Clean or replace the MicroTex filter. |
| Unusual noise during operation. | Obstruction in brush roll (Turbo Brush). Loose component. | Inspect and clear any debris from the Turbo Brush roll. Ensure all attachments and the motor head are securely fitted. |
| Dust escaping from vacuum. | Dust bag not installed correctly or damaged. Filter not seated properly. | Check dust bag installation; replace if damaged. Ensure MicroTex filter is correctly and securely in place. |
Specifications
- Model: 908423
- Brand: Numatic
- Manufacturer: NaceCare
- Product Dimensions: 19 x 22 x 16 inches
- Item Weight: 18 Pounds
- Motor Power: 680 watts (0.9 HP)
- Filter Type: HEPA Filter (MicroTex)
- Included Components: Accessory Kit (Hose, Wands, Turbo Brush, Hard-Floor Tool, Crevice Tool, Dusting Brush, Upholstery Nozzle)
- Special Feature: Automatic Cord Rewind
- Cordless: No
Warranty and Support
Warranty Information:
For specific warranty details, please refer to the warranty card included with your product or contact NaceCare customer service. Keep your proof of purchase for warranty claims.
Customer Support:
If you require further assistance or have questions not covered in this manual, please contact NaceCare customer support. Contact information can typically be found on the manufacturer's website or on the product packaging.
