Fellowes CRC34008 Cross-Cut Paper Shredder Instruction Manual

1. Important Safety Instructions

Please read these instructions carefully before using your Fellowes CRC34008 Cross-Cut Paper Shredder. Failure to follow these instructions may result in injury or damage to the shredder.

• Keep hands, jewelry, loose clothing, and hair away from the paper entry slot.
• Keep children and pets away from the shredder at all times.
• Unplug the shredder before moving, cleaning, or emptying the waste bin.
• Do not use aerosol products, petroleum-based lubricants, or flammable products on or near the shredder.
• Do not shred metal objects, large paper clips, or continuous forms.
• Ensure the shredder is placed on a level surface.
• Do not operate the shredder if the power cord is damaged.

2. Setup

Follow these steps to set up your shredder for first-time use.

1. Unpack the Shredder: Carefully remove the shredder and its components from the packaging.
   

   Image 1: Front view of the Fellowes CRC34008 Cross-Cut Paper Shredder.
2. Position the Waste Bin: Place the shredder head securely on top of the provided waste bin. Ensure it is seated correctly to activate the safety interlock.
   

   Image 2: The shredder head properly seated on its waste bin.

3. Connect Power: Plug the power cord into a grounded electrical outlet.
   

   Image 3: Rear view of the shredder, illustrating the power cord connection.

3. Operating Instructions

This section details how to operate your shredder safely and effectively.

1. Power On: Locate the control switch on the top of the shredder. Move the switch to the "ON" (I) position. The shredder is now ready for use.
   

   Image 4: Close-up of the shredder's control panel, showing the power switch.
2. Shredding Paper: Insert paper directly into the paper entry slot. The shredder will automatically start and stop once the paper has passed through. Do not exceed the maximum sheet capacity (refer to specifications).
3. Reverse Function: In case of a paper jam, move the control switch to the "REV" (R) position to clear the jam.
4. Power Off: When finished shredding, move the control switch to the "OFF" (O) position. For extended periods of non-use, unplug the shredder from the power outlet.

4. Maintenance

Regular maintenance ensures optimal performance and extends the life of your shredder.

• Emptying the Waste Bin: Empty the waste bin regularly to prevent paper jams and ensure continuous operation. Always unplug the shredder before removing the shredder head to empty the bin.
• Oiling the Cutters: For cross-cut shredders, it is recommended to oil the cutters periodically (e.g., after every 30 minutes of cumulative shredding or when performance decreases). Use only vegetable-based shredder oil. Apply a thin line of oil across the paper entry slot, then run a few sheets of paper through the shredder.
• Cleaning: Wipe the exterior of the shredder with a soft, dry cloth. Do not use abrasive cleaners or solvents.

5. Troubleshooting

Refer to this section for solutions to common issues.

6. Specifications

Key technical details for the Fellowes CRC34008 Cross-Cut Paper Shredder.

• Model: CRC34008
• Shred Type: Cross-Cut
• Sheet Capacity: Up to 8 sheets (70gsm paper)
• Shred Size: Approximately 4x35mm
• Waste Bin Capacity: Approximately 15 Liters
• Duty Cycle: 3-5 minutes on / 20-30 minutes off (approximate, to prevent overheating)
• Throat Width: 220mm
• Input Voltage: 120V AC, 60Hz (typical for North America)

Note: Specifications are approximate and may vary slightly.

7. Warranty and Support

For warranty information and technical support, please refer to the official Fellowes website or contact their customer service department.

Online Support: Visit www.fellowes.com/support

Customer Service: Refer to your product packaging or the Fellowes website for regional contact information.