1. Introduction
Thank you for choosing the Estry Replacement Battery. This manual provides essential information for the safe and effective use of your new battery. This battery is designed as a high-quality replacement for various Remington personal grooming devices.
Compatible Remington Models:
- PG-250
- 10468
- 457
- 4B3
- 5BF1 M
- 6BL2
- 7BFSL1
- 8B11L
- R-9100TLT
- RR-1
- R-TCT
- ULTW-1
- WER6000
- WER6200
- WER8000
- XLR3000
- XLR930
Please verify your device's model number to ensure compatibility before installation. This battery is not for AAA version devices.
2. Safety Information and Warnings
Your safety is paramount. Please read and adhere to all safety instructions before using this product.
CAUTION!
- NEW BATTERY PACK MUST BE FULLY CHARGED BEFORE USE.
- To reduce the risk of fire or burns, read instructions in the operating guide before using the battery.
- DO NOT attempt to disassemble, open, or service the battery pack.
- Replace only with the battery pack designated for this product.
- DO NOT store above 60°C (140°F).
- Keep batteries out of reach of children.
- Dispose of used batteries promptly and according to local regulations.
This battery is equipped with built-in protection against overcharge, over-discharge, over-voltage, and short circuits to enhance battery life and safety. It is RoHS approved for toxic-free materials and holds CE and ISO9001 certifications for quality assurance.
Image 2.1: Estry replacement battery showing important safety warnings printed on its label. The label advises full charging before use, warns against disassembly, and specifies storage temperature limits.
3. Setup and Installation
Replacing the battery in your Remington device requires careful handling. Always refer to your specific device's original instruction manual for detailed battery replacement procedures, as steps may vary by model.
- Power Off and Disconnect: Ensure your Remington device is completely powered off and disconnected from any charging source.
- Access Battery Compartment: Locate and open the battery compartment of your device. This may involve removing screws or prying open a casing. Use appropriate tools to avoid damage.
- Remove Old Battery: Carefully remove the old battery. Note its orientation and connections (if any) for proper installation of the new battery.
- Install New Battery: Insert the Estry replacement battery (Model: CS-PHN282SL) into the compartment, ensuring correct polarity and secure connections.
- Secure Compartment: Close and secure the battery compartment.
- Initial Charge: As per safety warnings, fully charge the new battery before its first use.
Image 3.1: Front view of the Estry replacement battery, showing its compact design and primary label with model number and specifications.
4. Operating and Charging
Once installed, the Estry replacement battery operates seamlessly with your compatible Remington device.
- First Use: Ensure the battery is fully charged before its initial operation.
- Charging: Use the original charger provided with your Remington device. Connect the device to the charger and allow it to charge until the charging indicator shows a full charge.
- Normal Operation: Use your device as you normally would. The battery is designed to provide reliable power for extended periods.
- Recharging: Recharge the battery when the device's performance diminishes or its low battery indicator activates.
5. Maintenance
Proper maintenance will extend the life and performance of your Estry replacement battery.
- Storage: If storing the device for an extended period, store it in a cool, dry place. Avoid temperatures above 60°C (140°F). It is recommended to store the battery with a partial charge (around 50%) rather than fully charged or fully depleted.
- Cleaning: Keep the battery contacts clean and free from dust or debris. Use a dry cloth to wipe them if necessary.
- Avoid Physical Damage: Do not drop, puncture, or expose the battery to strong impacts.
- Disposal: When the battery reaches the end of its life, do not dispose of it with household waste. Recycle it at an authorized battery recycling facility according to local environmental regulations.
Image 5.1: Angled view of the Estry replacement battery, highlighting its cylindrical cells and overall construction.
6. Troubleshooting
If you encounter issues with your Estry replacement battery, consider the following:
- Device Not Powering On:
- Ensure the battery is correctly installed with proper polarity.
- Verify the battery is fully charged.
- Check if the device's power switch is in the ON position.
- Battery Not Holding Charge:
- Confirm you are using the original and functional charger for your device.
- Ensure the charging contacts on both the device and charger are clean.
- Allow sufficient time for a full charge.
- Reduced Operating Time:
- Battery capacity naturally degrades over many charge cycles.
- Ensure the battery is fully charged before each use.
If problems persist after following these steps, please contact customer support.
7. Specifications
| Model Number: | CS-PHN282SL |
| Battery Type: | Ni-MH (Nickel-Metal Hydride) |
| Capacity: | 2000mAh |
| Watt-Hours (Wh): | 4.80Wh |
| Voltage: | 2.4V |
| Dimensions: | 50.00 x 29.00 x 14.50mm (1.97 x 0.57 x 1.14 inches) |
| Weight: | 80g / 2.82oz |
| Certifications: | ISO9001, RoHS, CE |
Image 7.1: Rear view of the Estry replacement battery, displaying manufacturing details and compliance marks such as CE and Made in China.
8. Warranty and Support
Estry stands behind the quality of its products.
- Warranty: This product comes with a 12-month warranty.
- Money Back Guarantee: A 14-day money-back guarantee is provided from the date of purchase.
- Customer Support: If you have any questions regarding compatibility, installation, or performance, or if you require professional suggestions, please contact our customer support. Refer to your purchase documentation for specific contact details.