1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Akozon Universal 14 LED Red Car Third Brake Light. Designed to enhance vehicle safety, this brake light features 14 bright red LEDs, an adjustable mounting bracket, and a durable, heat-resistant casing. It is powered by a 12V DC system and is suitable for various vehicle types.
Image 1.1: Akozon 14 LED Red Car Third Brake Light installed on a car's rear window, illustrating its function as an additional brake signal.
2. Safety Information
- Always disconnect the vehicle's battery before performing any electrical work to prevent short circuits or electrical shock.
- Ensure all wiring connections are secure and properly insulated to avoid electrical hazards.
- Mount the brake light in a location that does not obstruct the driver's view or interfere with other vehicle functions.
- Verify that the brake light operates correctly after installation before driving.
- If you are unsure about any installation steps, consult a qualified automotive technician.
3. Setup and Installation
Follow these steps to install your Akozon 14 LED Red Car Third Brake Light:
- Choose a Mounting Location: Select a suitable flat surface on your vehicle's rear window or parcel shelf. Ensure the location allows for clear visibility of the brake light from behind the vehicle.
- Clean the Surface: Thoroughly clean the chosen mounting surface with an alcohol wipe to remove any dust, grease, or debris. Allow it to dry completely.
- Prepare the Brake Light: The brake light comes with adhesive pads on its adjustable brackets. Peel off the protective backing from these adhesive pads.
Image 3.1: Detail of the adhesive pad on the mounting bracket, ready for installation.
- Mount the Light: Carefully position the brake light on the cleaned surface. Press firmly for several seconds to ensure good adhesion. The angle of the bracket is adjustable, allowing you to optimize the light's visibility.
Image 3.2: The adjustable bracket allows for precise positioning of the brake light.
- Wiring Connection: The brake light operates on 12V DC. Connect the red wire to the positive (+) 12V brake light circuit of your vehicle and the black wire to a suitable ground (-) point. It is recommended to tap into the existing brake light wiring.
Image 3.3: The red and black wires for connecting to the vehicle's 12V DC brake light circuit.
- Test Functionality: After connecting the wiring, re-connect the vehicle's battery. Press the brake pedal to verify that the new third brake light illuminates correctly.
The product's slimline design ensures it integrates discreetly into your vehicle while providing maximum longevity due to its durable casing.
Image 3.4: The slim profile of the brake light, emphasizing its elegant and durable design.
4. Operating Instructions
The Akozon Universal 14 LED Red Car Third Brake Light operates automatically. When properly installed and wired to your vehicle's brake light circuit, it will illuminate whenever the brake pedal is pressed, providing an additional visual warning to drivers behind you.
Image 4.1: The 14 bright red LEDs illuminated, demonstrating the light's high visibility.
5. Maintenance
This LED brake light requires minimal maintenance:
- Cleaning: Periodically clean the lens with a soft, damp cloth to ensure maximum light output. Avoid abrasive cleaners that could scratch the surface.
- Connection Check: Occasionally inspect the wiring connections to ensure they remain secure and free from corrosion.
- Adhesion Check: Verify that the adhesive pads are still firmly attached to the mounting surface. If necessary, re-secure or replace the adhesive.
6. Troubleshooting
If your Akozon 14 LED Red Car Third Brake Light is not functioning as expected, consider the following:
- Light does not illuminate:
- Check the wiring connections. Ensure the red wire is connected to a 12V positive brake light source and the black wire is connected to a good ground.
- Verify that the vehicle's main brake lights are functioning. If not, the issue may be with the vehicle's brake light circuit.
- Inspect the fuse for the brake light circuit in your vehicle.
- Light flickers or is dim:
- Check for loose or corroded wiring connections.
- Ensure the vehicle's battery voltage is stable (12V DC).
If these steps do not resolve the issue, contact customer support or a professional automotive technician.
7. Specifications
| Feature | Specification |
|---|---|
| Brand | Akozon |
| Model Number | Reminnbor71iabgzykd |
| UPC | 743562687660 |
| Material | Plastic |
| Voltage | 12V DC |
| Light Color | Red |
| LED Quantity | 14 LEDs |
| Total Length | Approx. 17 cm (6.7 inches) |
| LED Length | Approx. 14 cm (5.5 inches) |
| Width | Approx. 1.3 cm (0.5 inches) |
| Weight | Approx. 60 g |
| Special Feature | Adjustable Angle Bracket |
Image 7.1: Product dimensions, indicating a length of 17cm and a height of 6cm (including brackets).
Image 7.2: Visual representation of the product specifications.
8. Warranty and Support
For warranty information or technical support, please refer to the seller's policies on the platform where the product was purchased or contact Akozon customer service directly. Keep your purchase receipt as proof of purchase.